Tonelify
Black Friday40% off yearly

Gear compared

Marshall DSL20CR vs DSL40CR

Updated 6 min read3 sources

Both are Marshall all-valve combos with the same two channels, Classic Gain and Ultra Gain, one 12-inch Celestion rated at 80 watts, the same shared EQ with Tone Shift, digital reverb, a series effects loop and an emulated out by Softube. The DSL20CR is 20 watts with 3 ECC83 and 2 EL34 valves, a Gain and a Volume on each channel and one Reverb knob, at 16.3 kg. The DSL40CR is 40 watts with 4 ECC83 and 2 EL34 valves, and adds two modes on each channel, a reverb for each channel, two master volumes, a loop switch and MIDI In, at 22.9 kg.

Choose the DSL20CR for the lighter, simpler amp that drops to 10 watts at home. Choose the DSL40CR for four sounds from two channels, a second master for solos and a separate reverb level on each channel. Every figure on this page comes from Marshall's two quick start guides and its DSL20 support page.

Match a song to my amp7 days free, $0 today
A row of black chicken-head knobs on a brushed gold amp panel

Side by side

The DSL20CR column is from Marshall's DSL20CR and DSL20HR quick start guide and its DSL20 Combo support page on the effects loop, the DSL40CR column from Marshall's DSL40CR and DSL100HR quick start guide. Where a guide lists no such control or socket, the cell says None.

From Marshall's DSL20CR and DSL20HR quick start guide and DSL20 support page, and its DSL40CR and DSL100HR quick start guide.
Marshall DSL20CRMarshall DSL40CR
Power20 W; the Output switch drops it to 10 W or to standby40 W; the Output switch drops it to 20 W or to standby
Valves3 ECC83 and 2 EL344 ECC83 and 2 EL34
ChannelsClassic Gain and Ultra Gain, each with Gain and VolumeClassic Gain and Ultra Gain, each with Gain and Volume
ModesNoneClean and Crunch on Classic Gain, OD1 and OD2 on Ultra Gain
EQTreble, Middle, Bass, Presence, Resonance and Tone Shift, shared by both channelsThe same, shared by both channels
ReverbDigital, one Reverb knobDigital, Classic Reverb and Ultra Reverb
Master volumeNone, each channel's Volume sets its levelMaster 1 and Master 2, with Master Select
Effects loopSeries send and returnSeries send and return, with a Loop On/Off switch
FootswitchPEDL-90012 channel footswitch, suppliedPEDL-90012 channel footswitch supplied, PEDL-91016 optional
MIDINoneMIDI In
Emulated out3.5 mm jack, cabinet emulation by Softube1/4-inch jack, cabinet emulation by Softube
Speaker outputs3 jacks, for 16 and 8 ohm loads5 jacks, for 16, 8 and 4 ohm loads
SpeakerOne 12-inch Celestion Seventy 80, 80 W, 16 ohmsOne 12-inch Celestion V-Type, 80 W, 16 ohms
Weight16.3 kg (about 36 lb)22.9 kg (about 50 lb)
Size500 wide, 420 high, 250 deep, in mm620 wide, 490 high, 252 deep, in mm
Audio InFor playing along to musicFor playing along to music

Modes: four sounds against two channels

Both amps have the same two channels, Classic Gain and Ultra Gain, and both guides describe a channel's Gain the same way: it adjusts the amount of input gain sent into the preamp stage, and running a higher setting increases the level of distortion. The DSL40CR then splits each channel in two. Its Clean/Crunch button gives Classic Gain two modes that, in Marshall's words, take your sound from clean to overdriven tones, and its OD1/OD2 button gives Ultra Gain two modes that take it from distorted to heavy gain tones. A status LED beside each button lights green for the first mode and red for the second.

The DSL20CR has no mode buttons. Its Channel Select button switches between the two channels, with a green light for Classic Gain and a red light for Ultra Gain, and within a channel the sound moves with the Gain knob alone. That is why Tonelify's crunch setting for the DSL20CR runs the Classic Gain channel's Gain higher than the DSL40CR's Crunch mode needs.

The EQ is the same on both: Treble, Middle, Bass, Presence and Resonance with a Tone Shift switch, one set for the two channels. Both guides say Tone Shift reconfigures the preamp EQ, accentuating the high and low frequencies and cutting the mids, and both carry the same note that the EQ controls are linked, so altering one control can change the way the others behave.

Two masters against one Volume per channel

On the DSL20CR each channel has a Gain and a Volume, and that Volume is the only volume control: Marshall's guide says it controls the volume level of its channel. Turn Gain up and Volume down for drive at a lower level. The DSL40CR keeps the channel Volumes and adds a master section: Master 1 and Master 2 each set an overall volume level, Master Select switches between them, and the Master LED turns green for Master 1 and red for Master 2.

Two masters make a solo boost. Set Master 2 a little above Master 1 and switch to it when the solo starts; both are overall volumes, so the lift works on whichever channel is playing. On the DSL20CR the nearest thing is setting the Ultra Gain channel's Volume a little louder than Classic Gain's, so the channel switch doubles as a rhythm to lead switch.

Reverb splits the same way. The DSL20CR has one Reverb knob, which Marshall says controls the overall reverb level. The DSL40CR has Classic Reverb and Ultra Reverb, each setting the reverb level of its own channel, so a clean part can carry more reverb than a lead without touching a knob between them.

Power, valves, speaker and weight

Marshall rates the DSL20CR at 20 watts and the DSL40CR at 40. On each, the Output switch halves the power or places the amp into standby: from 20W down to 10W on the DSL20CR, from 40W down to 20W on the DSL40CR. Both run 2 EL34 power valves, and the DSL40CR has 4 ECC83 preamp valves to the DSL20CR's 3.

Each combo carries one 12-inch Celestion rated at 80 watts and 16 ohms: a Seventy 80 in the DSL20CR and a V-Type in the DSL40CR. The DSL40CR is the bigger box, 620 mm wide and 22.9 kg against the DSL20CR's 500 mm and 16.3 kg.

For extension cabinets the DSL20CR has three speaker jacks, for one 16-ohm cabinet, or one 8-ohm cabinet or two 16-ohm cabinets. The DSL40CR has five and adds a 4-ohm pair, for one 4-ohm cabinet or two 8-ohm cabinets. Marshall warns on both that any other speaker configuration may stress or damage the amp.

Match a song to my amp7 days free, $0 today

Pedals, MIDI and recording

Both have a series effects loop on the back: Send goes to your pedals and their output comes back to Return. The DSL40CR adds a Loop On/Off switch on the front panel, with an LED that turns green while the loop is on. The DSL20CR has no loop switch, and Marshall's support page for it says the footswitch must be plugged in for the loop to work.

Both come with Marshall's PEDL-90012 channel footswitch. The DSL40CR also takes the optional PEDL-91016 footswitch and has a MIDI In socket for an external MIDI device; the DSL20CR has neither.

For recording or headphones, both have an Emulated Out, which Marshall calls a frequency-compensated line level output with cabinet emulation by Softube, so the sound from it includes a simulated speaker and cabinet. On the DSL20CR it is a 3.5 mm jack, on the DSL40CR a 1/4-inch jack. Both also have an Audio In for an external device to practise with or jam along to.

The same starting points on both

These are Tonelify's starting settings from each amp's gear page, not Marshall's numbers: neither quick start guide gives knob settings. The values are the numbers on the knobs. The DSL40CR rows leave out the channel Volume and the masters, which set loudness; on the DSL20CR the channel Volume is the only volume control, so it is in the row.

Tonelify starting points from the DSL20CR and DSL40CR gear pages. Move one control at a time from here.
SoundDSL20CRDSL40CR
CleanClassic Gain, Gain 3 to 4, Volume 5, Treble 6, Middle 5, Bass 5, Presence 5, Reverb 3Classic Gain, Clean mode, Gain 3 to 4, Treble 6, Middle 5, Bass 5, Presence 5, Classic Reverb about 3
CrunchClassic Gain, Gain 7 to 8, Volume 4, Treble 6, Middle 6 to 7, Bass 5, Presence 6, Reverb 2Classic Gain, Crunch mode, Gain 5 to 7, Treble 6, Middle 6 to 7, Bass 5, Presence 6, Classic Reverb about 2
Hard rockUltra Gain, Gain 4 to 5, Volume 4, Treble 6, Middle 6, Bass 5, Presence 6, Reverb 2Ultra Gain, OD1 mode, Gain 5 to 6, Treble 6, Middle 6, Bass 5, Presence 6, Ultra Reverb about 2
MetalUltra Gain, Tone Shift on, Gain 6 to 7, Volume 4, Treble 6, Middle 5, Bass 6, Presence 6, Resonance 6Ultra Gain, OD2 mode, Tone Shift on, Gain 6 to 7, Treble 6, Middle 5, Bass 6, Presence 6, Resonance 5

Settings for a song, on either amp

A style setting gets you close. A particular record needs its own numbers, and the DSL40CR's modes and masters move where they land compared with the DSL20CR's two channels. Tonelify gives song settings for the controls each of these amps actually has, so the answer for one is never a copy of the other.

Common questions

Is the DSL40CR twice as loud as the DSL20CR?

No. Marshall rates the DSL40CR at 40 watts and the DSL20CR at 20, and twice the power is a step up in loudness, not a doubling. Marshall gives no sound pressure figure for either. Each also halves its power on the Output switch, so the DSL40CR at 20 watts and the DSL20CR at full power are rated the same.

Does the DSL20CR have clean and crunch modes like the DSL40CR?

No. Marshall's guide gives the DSL20CR two channels, Classic Gain and Ultra Gain, each with a Gain and a Volume and no mode button. Crunch on the DSL20CR is the Classic Gain channel with its Gain turned up. The DSL40CR adds a Clean/Crunch button on Classic Gain and an OD1/OD2 button on Ultra Gain.

Which has a master volume, the DSL20CR or the DSL40CR?

The DSL40CR, with two: Master 1 and Master 2 each set an overall volume level, and Master Select switches between them. The DSL20CR has no master knob; each channel's Volume sets the level of that channel.

Can you switch the effects loop off on the DSL20CR?

Marshall lists no loop switch for the DSL20CR. Its loop is a series send and return, and Marshall's support page says the footswitch must be plugged in for the loop to work. The DSL40CR has a Loop On/Off switch on the front panel, with an LED that lights green while the loop is on.

Which can drive a 4-ohm cabinet?

Only the DSL40CR. Its five speaker jacks take one 16-ohm cabinet, one 8-ohm cabinet or two 16-ohm cabinets, or one 4-ohm cabinet or two 8-ohm cabinets. The DSL20CR's three take one 16-ohm cabinet, or one 8-ohm cabinet or two 16-ohm cabinets. On both, Marshall says to use a proper speaker cable, never a shielded guitar cable.

Which is better for playing at home?

The DSL20CR is lighter, 16.3 kg against 22.9 kg, and its Output switch takes it down to 10 watts, where the DSL40CR's lowest setting is 20. Both have the emulated out, which Marshall's guides describe as a line level output for headphones, and an Audio In to play along to music.

Do DSL40CR settings work on a DSL20CR?

Mostly. Both guides describe the same EQ knobs, the same Tone Shift and the same Gain. The DSL40CR's Clean mode becomes the DSL20CR's Classic Gain channel at low Gain and Crunch mode the same channel with Gain higher; OD1 and OD2 become the Ultra Gain channel, with Gain lower for OD1 and higher for OD2. Leave the masters out and set the level with the channel Volume.

Sources

Gear in this guide

Settings for your own amp

This guide covers what is true of every rig. For a specific song on a specific amp, Tonelify reads the documented chain behind the recording and returns gain, bass, middle, treble and presence values for the controls your amp actually has. A first plan starts with 7 days free, $0 today.

Keep reading