Tonelify
Black Friday40% off yearly

Gear compared

Peavey 6505+ vs Mesa Dual Rectifier

Updated 7 min read2 sources

Both are high-gain tube heads with four 6L6 power tubes. The Peavey 6505+ is the simpler amp: 120 watts RMS and two channels, Rhythm, with a Crunch and a Bright switch, and Lead, each with its own Pre and Post gain, EQ, Resonance and Presence, at 21.91 kg. The Mesa Dual Rectifier has three channels with eight modes between them, lets each channel choose 50 or 100 watts and a tube or diode rectifier, and adds a Solo level on the footswitch.

Choose the 6505+ for fewer decisions: two channels, a three-button footswitch and a Preamp Out. Choose the Dual Rectifier for three channels, each set up with its own mode, wattage and rectifier, and a footswitchable Solo boost. Every figure on this page comes from Peavey's 6505+ operation manual and Mesa's owner's manual for the Multi-Watt Dual and Triple Rectifier.

Match a song to my amp7 days free, $0 today
A black tube amp head on a 4x12 cabinet, seen from behind on a smoky stage

Side by side

The 6505+ column is from Peavey's operation manual, the Dual Rectifier column from Mesa's owner's manual for the Multi-Watt Dual and Triple Rectifier heads. Mesa's manual gives no weight or size, so those cells say so rather than guessing.

From Peavey's 6505+ operation manual and Mesa's Multi-Watt Dual and Triple Rectifier owner's manual.
Peavey 6505+Mesa Dual Rectifier
Power120 W RMS into 16, 8 or 4 ohms100 W, or 50 W on any channel set to 50 Watt
Power switchesStandby onlyMulti-Watt 50 or 100 W on each channel, Spongy or Bold for the whole amp, and Standby
Power tubesFour 6L6GCFour 6L6, with a Bias Select switch for EL34
Preamp tubesSix 12AX7Five 12AX7
RectifierNo rectifier switchTube Tracking, with 5U4G tubes, or Diode, chosen on each channel
ChannelsTwo: Rhythm and LeadThree
Modes and switchesCrunch and Bright, on Rhythm onlyClean and Pushed on Channel 1; Raw, Vintage and Modern on Channels 2 and 3
Controls per channelPre, Low, Mid, High, Post, Resonance and PresenceGain, Treble, Mid, Bass, Presence and Master
Overall volumeNone, each channel's Post sets its levelOutput, plus a Solo level on the footswitch
Effects loopSend and return, on the footswitchSeries, with Send Level and a six-position Assign control
FootswitchMetal, three buttons: Effects, Crunch and Channel, suppliedDIN jack: channels, Solo, the loop and a silent Tuner
Extra outputsPreamp Out, +10 dBVSlave Out with its own level, and Tuner Out
Speaker jacksTwo in parallel, with a 4, 8 or 16 ohm switchTwo 4 ohm, two 8 ohm and one 16 ohm
StandbyYesYes, after at least 30 seconds of warm-up
Weight21.91 kg (48.3 lb)Not given in Mesa's manual
Size67.6 wide, 25.4 high, 29.8 deep, in cmNot given in Mesa's manual

Two channels against three

The 6505+ has a Rhythm channel and a Lead channel, chosen with the Channel Select switch: pressed in, the Lead channel plays and the red LED by its Pre control lights; out, the Rhythm channel plays and its green LED lights. Peavey says the Pre and Post Gain controls work the same way on both, but the Lead channel has more pregain, and it suggests Pre at the lower, cleaner settings (0-4) on Rhythm and at the mid to upper settings (5-10) on Lead, with Post set for overall volume. Two switches change the Rhythm channel only: Crunch boosts its gain to a medium distortion, and Bright adds a preset treble boost of 6 dB at 2 kHz.

The Dual Rectifier has three channels and eight modes. Channel 1 has Clean, which Mesa calls the lowest gain circuit of the eight, and Pushed, which it calls perfect for crunch rhythm or medium gain soloing. Channels 2 and 3 each have Raw, the lowest gain of the three, Vintage, the famous liquid Recto voice, and Modern, which Mesa sums up in one word, aggressive, with a tighter low end and a more present top end. Mesa describes the amp as three separate multi-mode amplifiers built onto one chassis: the channels look identical, but each Gain control sits at a different point in its channel's circuit.

Both give every channel its own tone controls. On the 6505+ that is Pre, Low, Mid, High and Post, plus Resonance and Presence in the power amp. Peavey calls the EQ passive, so turning a control counterclockwise cuts its band, and calls Resonance unique to Peavey instrument amplifiers: the Dual Rectifier has no such control. On the Dual Rectifier each channel has Gain, Treble, Mid, Bass, Presence and Master, and Mesa calls Gain and Treble the most powerful controls in all three channels, with the best sounds somewhere in their middle regions.

Power: one setting against three choices per channel

Peavey rates the 6505+ at 120 W RMS into 16, 8 or 4 ohms, from four 6L6GC power tubes, and its manual lists no switch to change that beyond Standby. The bias test terminals are on the back, and Peavey says the adjustment should only be done by a qualified technician.

The Dual Rectifier makes power part of each channel's sound. Every channel has a Multi-Watt switch: at 50 Watt the outside pair of the four tubes plays, for a clippable 50 watts, and at 100 Watt all four 6L6 tubes do, which Mesa prefers for pristine clean sounds and tight-tracking high gain sounds. Every channel also has its own Rectifier Select switch on the back. Diode, in Mesa's words, offers more punch and a tighter attack with added brightness; Tube Tracking brings in one 5U4 rectifier tube at 50 watts and both at 100, for a looser, saggier response.

One more switch covers the whole amp. Mesa says Spongy works like a built-in Variac, switching the incoming AC line voltage down to about 95 volts for additional sag, and Bold gives maximum power, clean headroom and volume. The Dual Rectifier is shipped with 6L6 tubes, and its Bias Select switch lets it run EL34s instead, though Mesa recommends the 6L6 for reliability.

Volume, Solo and the effects loop

The 6505+ has no master volume: each channel's Post Gain sets its overall volume, so balancing Rhythm against Lead is a matter of two Post knobs. Its effects loop has a Send and a Return on the back, switched from the footswitch's left button, and Peavey says only non-gain effects such as chorus, reverb and delay should go in it. With the footswitch plugged in, Effects must be selected, its LED lit, for the loop to work.

The Dual Rectifier has a Master on each channel and two more levels on the front: Output, which sets the overall volume of the amp, and Solo, an additional final output level wired in parallel with Output that the footswitch calls up. Both are part of the effects loop's return circuit, so in Loop Bypass they do nothing and the channel Masters become the final output controls. Solo also needs the footswitch connected, and it can be set above Output but not below it.

Mesa's loop is wired in series, with a Send Level control to match your processor and an Assign control on the back that has Loop Bypass and five other positions, marked Loop On, CH 1, CH 2, CH 3 and FTSW. Mesa says a small volume drop when the loop comes in is normal, and that Send Level brings it back to about unity even with nothing patched in.

Match a song to my amp7 days free, $0 today

Recording, cabinets and footswitches

For recording, the 6505+ has a Preamp Out on the back, which Peavey says can feed a mixing console or tape recorder through a shielded instrument cable without affecting the amp's normal operation. It carries the preamp only, at a nominal +10 dBV, so a cabinet simulator or impulse response goes after it. The Dual Rectifier has a Slave Out with its own level, taking a signal from the speaker jack, which Mesa describes for running additional power amps or sending a wet signal to other amps, and a Tuner Out that is active at all times.

For cabinets, the 6505+ has two parallel speaker jacks and an Impedance Selector set to 4, 8 or 16 ohms, with 4 ohms the minimum; two cabinets of equal impedance take half their value, so two 16-ohm cabinets go on 8. The Dual Rectifier has two 4-ohm jacks, two 8-ohm jacks and one 16-ohm jack instead of a switch. Mesa says its own 4x12 cabinets are 8 ohms, and that two 8-ohm speakers go on the 4-ohm outputs.

The 6505+ comes with a metal three-button footswitch: Effects on the left, Crunch in the centre and Channel on the right, all push on and push off. For it to change channels, the front Channel Select switch must be pressed in. The Dual Rectifier's footswitch plugs into a DIN jack and covers the channels, Solo, the loop and a Tuner button that mutes the signal for silent tuning; for it to change channels, the rear Channel Select rotary switch must be set to Footswitch.

The same starting points on both

These are Tonelify's starting settings from each amp's gear page, not Peavey's or Mesa's numbers. The 6505+ values are the numbers on its knobs. The Dual Rectifier's knobs carry no numbers and Mesa's manual writes every position as a clock time, so its values are clock positions.

Tonelify starting points from the 6505+ and Dual Rectifier gear pages. Move one control at a time from here.
Sound6505+Dual Rectifier
CleanRhythm channel, Bright in, Pre 3, Low 5, Mid 5, High 6, Resonance 4, Presence 4Channel 1, Clean mode, Gain 12:00 to 1:00, Treble 12:00 to 1:00, Mid 9:00 to 10:00, Bass 11:00, Presence 1:00
CrunchRhythm channel, Crunch in, Pre 6, Low 5, Mid 6, High 6, Resonance 4, Presence 5Channel 1 Pushed or Channel 2 Raw, Gain 1:00 to 2:00, Treble 1:00, Mid 12:00 to 1:00, Bass 10:00 to 11:00, Presence 12:00
MetalLead channel, Pre 6, Low 6, Mid 4, High 6, Resonance 5, Presence 5Channel 3, Modern mode, 100 Watt, Diode, Gain 1:00 to 2:00, Treble 12:00 to 1:00, Mid 10:00 to 11:00, Bass 10:00 to 11:00, Presence 12:00 to 1:00
LeadLead channel, Pre 7, Low 5, Mid 7, High 5, Resonance 4, Presence 5Channel 2, Vintage mode, Tube Tracking, Gain 1:00 to 2:00, Treble 12:00, Mid 12:00 to 1:00, Bass 11:00, Presence 10:00 to 11:00

Settings for a song, on either amp

A style setting gets you close. A particular record needs its own numbers, and they land differently on the 6505+'s numbered knobs than on the Dual Rectifier's clock positions. Tonelify gives song settings for the controls each of these amps actually has, so the answer for one is never a copy of the other.

Songs from Rectifier rigs

Common questions

Which is louder, the 6505+ or the Dual Rectifier?

Peavey rates the 6505+ at 120 W RMS into 16, 8 or 4 ohms. Mesa gives the Dual Rectifier 100 watts with a channel's Multi-Watt switch on 100 Watt and 50 on 50 Watt, and says Spongy reduces the power somewhat. Neither maker gives a sound pressure figure, and Mesa warns that these amplifiers are capable of extremely loud volumes.

Does the 6505+ have a solo boost like the Dual Rectifier?

Not as a separate control: Peavey's manual lists no Solo or master volume. One way is to set the Lead channel's Post a little above the Rhythm channel's, so the channel button on the footswitch is also a step up in volume. The Dual Rectifier has a Solo control, a second output level that the footswitch switches in, which works only with the footswitch connected and the effects loop on.

Why does the Output knob do nothing on the Dual Rectifier?

Output and Solo are part of the effects loop's return circuit, so they only work while the loop is switched in. Turn the Loop Assign control on the back out of Loop Bypass to any of its other five positions; in Loop Bypass, the channel Masters are the final output controls. The 6505+ has no such step, because each channel's Post Gain sets its volume.

Can either amp run EL34 tubes?

The Dual Rectifier can. Its rear Bias Select switch has 6L6 and EL34 positions, and Mesa says to make sure it matches the tubes fitted, or tubes can fail. It is shipped with 6L6s, which Mesa recommends for reliability, and its rear panel says Tube Tracking is best with EL34s. Peavey lists four 6L6GC power tubes for the 6505+ and no EL34 option, with bias adjustment for a qualified technician only.

How do you connect a cabinet to each amp?

On the 6505+, use either of the two parallel speaker jacks and set the Impedance Selector to the cabinet's impedance, 4, 8 or 16 ohms, never below 4; two equal cabinets take half their value. The Dual Rectifier has no switch: use the jack that matches the load, from two 4-ohm, two 8-ohm and one 16-ohm jack. Mesa's 4x12 cabinets are 8 ohms, and two 8-ohm speakers go on the 4-ohm jacks.

Can you record either amp without a microphone?

Neither manual lists a cabinet-simulated output. The 6505+'s Preamp Out sends the preamp signal to a mixing console or recorder, so put a cabinet simulator or impulse response after it. The Dual Rectifier's Slave Out takes its signal from the speaker jack, and Mesa describes it for running additional power amps or sending a wet signal to other amps.

Where do I start for metal on each amp?

On the 6505+, the Lead channel: Pre 6, Low 6, Mid 4, High 6, Resonance 5 and Presence 5, inside Peavey's 5 to 10 range for Lead Pre Gain. On the Dual Rectifier, Channel 3 in Modern at 100 Watt and Diode: Gain 1:00 to 2:00, Treble 12:00 to 1:00, Mid 10:00 to 11:00, Bass 10:00 to 11:00 and Presence 12:00 to 1:00. These are Tonelify's starting points, not the makers' numbers.

Sources

Gear in this guide

Settings for your own amp

This guide covers what is true of every rig. For a specific song on a specific amp, Tonelify reads the documented chain behind the recording and returns gain, bass, middle, treble and presence values for the controls your amp actually has. A first plan starts with 7 days free, $0 today.

Keep reading