Tonelify
Black Friday40% off yearly

Gear compared

Valeton GP-200 vs GP-200LT vs GP-200JR

Updated 6 min read6 sources

The GP-200LT and GP-200JR are smaller versions of the Valeton GP-200 with the same effects library, so the sound is the same and the hardware is what differs. The GP-200 has 8 footswitches, a built-in expression pedal, a row of amp knobs, 5-pin MIDI and XLR outputs, and weighs 2.37 kg. The GP-200LT has 4 footswitches, no pedal, 1/8-inch TRS MIDI, two EXP/FS jacks and a headphone volume knob, at 1.25 kg. The GP-200JR has 3 footswitches, a built-in pedal and XLR outputs, with no MIDI jacks, at 1.55 kg.

All three have 11 effect modules that run at once, 140+ amp and cab models, 100+ effects, 20 IR slots, a 180 second looper, 100 drum patterns and a 6-in/4-out USB audio interface. Pick the LT for the smallest board with MIDI, the JR for a pedal on a small board, and the GP-200 for the most footswitches. Every figure on this page comes from Valeton's own manuals and product pages.

Match a song to my amp7 days free, $0 today
A large rotary encoder next to a small blank display on a practice amp

GP-200 vs GP-200LT vs GP-200JR at a glance

One row per difference, from the Technical Specifications and Panel Introduction in each user manual, with the product pages where the manual leaves a gap. Valeton calls the LT and the JR Lite versions of the GP-200, built on the same technology.[2]

Patch slots differ by one: the JR's 99 factory patches sit in 33 banks of three (A, B and C),[3] while the GP-200 and LT hold 100 in banks of four. That layout follows the footswitch count.

From Valeton's GP-200 (firmware V1.7.4), GP-200LT and GP-200JR (firmware V1.8.0) user manuals and the three product pages.
GP-200GP-200LTGP-200JR
Footswitches843 (product page)
Built-in expression pedalYesNoYes
EXP/FS jacksOne 1/4-inch TRSTwo 1/4-inch TRS: 2 pedals or up to 4 footswitchesOne 1/4-inch TRS (product page)
Amp knobs on the panelYes, a row for the AMP moduleNoNo
Headphone volume knobNoYesNot on the panel page
MIDI IN/OUT (THRU)5-pin1/8-inch TRSNo MIDI jacks listed
Balanced outputsXLR1/4-inch TRSXLR and 1/4-inch TRS (product page)
Patch slots256, 100 factory256, 100 factory255, 99 factory
Size (W x D x H)345 x 220 x 62.5 mm253 x 165 x 56 mm281 x 166 x 57 mm
Weight2.37 kg1.25 kg1.55 kg

What all three share

Both Lite product pages say the unit is equipped with the GP-200's same effects library: 140 amplifier and cabinet simulations, over 100 stompbox effects and 20 factory cab IR slots.[5] The three manuals list the same 11 modules, which can all run at once and be moved in the chain.

The rest of the spec sheet matches too: 24-bit 44.1 kHz conversion, a 4.3-inch colour screen, a 180 second looper, 100 drum patterns, an FX loop, an aux input and a DC 9V 1000mA centre negative supply. Over USB-C each one is a 6-in/4-out audio interface with re-amp and loopback.

From the Technical Specifications in all three Valeton user manuals; the same figure appears for each unit.
FeatureGP-200, GP-200LT and GP-200JR
Effect modules11, can be used simultaneously
Conversion24-bit, 44.1 kHz
Signal to noise110 dB
LooperUp to 180 seconds
Drum machine100 patterns
Guitar input impedance4.7 MΩ (acoustic), 1 MΩ (electric), 10 kΩ (line)
Headphone output1/8-inch stereo, 22 Ω
USBUSB 2.0 Type-C, records at 44.1 kHz, 16 or 24-bit
PowerDC 9V, 1000mA, centre negative

GP-200 vs GP-200LT

The LT is the GP-200 cut down to four footswitches and no pedal, at a little over half the weight. It keeps MIDI, on 1/8-inch TRS jacks instead of 5-pin, and it gains a second EXP/FS jack, so you can add two expression pedals or up to four footswitches.[5] Its balanced outputs are 1/4-inch TRS jacks instead of XLR.

Two panel changes matter on a desk. The LT has its own PHONES knob, separate from MASTER, which the GP-200 does not. And it drops the GP-200's row of amp knobs, so amp settings are made in the AMP module's edit screen with the Quick Access knobs.

Match a song to my amp7 days free, $0 today

GP-200 vs GP-200JR

The JR keeps the GP-200's built-in expression pedal and its XLR outputs, and cuts the footswitches to three: [-], [+] and [CTRL], with the tuner on [-] and [+] together.[3] It has no MIDI jacks; MIDI over USB is there in the interface's Normal mode. Like the LT it has no amp knobs.

Valeton's JR manual reuses the LT manual's text in places. It says 4 footswitches, a pair of EXP/FS jacks and 1/4-inch TRS balanced outputs, while the JR product page lists 3 footswitches, one EXP/FS jack and XLR outputs.[6] The product page fits the JR's own patch banks of three and the manual's GND/LIFT switch for the two XLR connectors.

GP-200LT vs GP-200JR

This is the choice between MIDI and a pedal. The LT has four footswitches, MIDI jacks and two EXP/FS jacks, and is the smaller and lighter of the two at 253 mm wide and 1.25 kg. The JR has three footswitches and a built-in expression pedal that controls up to 3 effect parameters, at 281 mm wide and 1.55 kg.

For a desk or an audio interface setup, the LT's headphone knob and smaller size help. For playing wah or volume swells without buying a pedal, the JR has one built in. Both run the same patches and effects, so the sound does not decide it.

Settings carry across all three

Since the amp, cab and effect models are the same library, a GP-200 setting works on an LT or a JR: models such as Dark Twin, Tweedy and Solo100 LD carry the same names in all three manuals. On the LT and JR, which have no amp knobs, open the AMP module with its button and set the values on the screen.

The Valeton GP-200 page has Tonelify's starting settings for its amp models, and they apply to all three units. When you want a particular song, Tonelify writes the amp model, the knob values and the effects for that song on the GP-200's own scale.

Common questions

What is the difference between the Valeton GP-200 and GP-200LT?

The GP-200LT has 4 footswitches to the GP-200's 8, no built-in expression pedal, no amp knobs, MIDI on 1/8-inch TRS jacks instead of 5-pin, and 1/4-inch TRS balanced outputs instead of XLR. It adds a second EXP/FS jack and a headphone volume knob. It weighs 1.25 kg to the GP-200's 2.37 kg. The effects library is the same.

What is the difference between the GP-200LT and the GP-200JR?

The LT has 4 footswitches, MIDI jacks, two EXP/FS jacks and a headphone volume knob, at 253 mm wide and 1.25 kg. The JR has 3 footswitches, a built-in expression pedal and XLR outputs, with no MIDI jacks, at 281 mm wide and 1.55 kg. Both use the GP-200's effects library and 11 modules.

Do the GP-200LT and GP-200JR sound the same as the GP-200?

Valeton says both are equipped with the GP-200's same effects library: 140 amp and cabinet simulations, over 100 stompbox effects and 20 factory cab IR slots. The three manuals list the same 11 modules, 24-bit 44.1 kHz conversion and 110 dB signal to noise. The differences are in the hardware, not the sound.

Does the Valeton GP-200LT have an expression pedal?

No. The GP-200LT has no built-in pedal, but it has two 1/4-inch TRS EXP/FS jacks that take two external expression pedals or up to four footswitches. The GP-200 and the GP-200JR each have a built-in expression pedal, and Valeton says it controls up to 3 effect parameters.

Does the GP-200JR have MIDI?

Not on jacks. The GP-200JR's manual and product page list no MIDI connectors, while the GP-200 has 5-pin MIDI IN and OUT (THRU) and the GP-200LT has the same on 1/8-inch TRS jacks. Over USB, the JR's Normal mode is a 6-in/4-out audio interface with MIDI.

How many footswitches does the GP-200JR have?

Three, by Valeton's product page: [-], [+] and [CTRL], and its 99 factory patches sit in banks of three, A to C. The JR user manual says 4 in its overview and panel pages, text it shares with the GP-200LT manual. The GP-200LT has 4 and the GP-200 has 8.

Which GP-200 has XLR outputs?

The GP-200 has two balanced XLR outputs. The GP-200JR's product page lists two balanced XLR and two balanced 1/4-inch TRS outputs, and its manual describes a GND/LIFT switch for the two XLR connectors. The GP-200LT's balanced outputs are 1/4-inch TRS jacks, with no XLR.

How big and heavy are the GP-200, GP-200LT and GP-200JR?

By Valeton's specifications, the GP-200 is 345 x 220 x 62.5 mm and 2.37 kg, the GP-200LT 253 x 165 x 56 mm and 1.25 kg, and the GP-200JR 281 x 166 x 57 mm and 1.55 kg. All three run on DC 9V at 1000mA, centre negative.

How many patches do the GP-200LT and GP-200JR hold?

The GP-200LT holds 256 patches, 100 of them factory, the same as the GP-200. The GP-200JR holds 255, with 99 factory patches. Both can load 20 user IRs, and both have a 180 second looper and 100 drum patterns.

Can I use GP-200 settings on a GP-200LT or GP-200JR?

Yes. The amp, cab and effect models come from the same library, so a GP-200 setting carries over: models such as Dark Twin and Solo100 LD have the same names in all three manuals. The LT and JR have no amp knobs on the panel, so set the amp on the AMP module's edit screen with the Quick Access knobs.

Which one has a headphone volume knob?

The GP-200LT. Its manual's panel page lists a PHONES knob, separate from MASTER, and Valeton's product page calls it an independent headphone volume knob. The GP-200JR's panel page lists no PHONES knob, though one passage of its manual mentions one, and the GP-200's manual has none. All three have a 1/8-inch headphone output.

Sources

The numbers in brackets in the text point to this list.

Gear in this guide

Settings for your own amp

This guide covers what is true of every rig. For a specific song on a specific amp, Tonelify reads the documented chain behind the recording and returns gain, bass, middle, treble and presence values for the controls your amp actually has. A first plan starts with 7 days free, $0 today.

Keep reading