Tonelify
Black Friday40% off yearly

Gear compared

NUX MG-30 vs Line 6 POD Go

Updated 7 min read5 sources

Both are floor modellers with a colour screen, a built-in expression pedal, third-party IR loading, an effects loop for the 4-cable method and USB recording. The POD Go has the bigger library, 107 amps and preamps and 46 cabs from Line 6's HX family, 256 presets with four snapshots each, six stomp footswitches and a dedicated Amp Out. The MG-30 has 35 amp models, 10 NAM slots with its GEN2 firmware, 11 movable blocks, three footswitches with a dual footswitch in the box, scenes that can change models, and a longer looper with drums.

Choose the POD Go for more models and a pedalboard of switches under your feet. Choose the MG-30 to load NAM captures, to order the blocks freely and to practise with drums. Every figure on this page comes from NUX's and Line 6's own manuals and product pages.

Match a song to my amp7 days free, $0 today
A row of stompboxes on a pedalboard, lit in amber

Side by side

The MG-30 column is from NUX's user manual and its MG-30 page, with the looper and patch figures from the control parameter sheet Aria, which carries NUX in Japan, published. The POD Go column is from Line 6's 2.50 Owner's Manual and its POD Go page. Where a maker does not list a feature, the cell says so rather than guessing.

From NUX's MG-30 user manual and product page, Aria's MG-30 parameter sheet, and Line 6's POD Go 2.50 Owner's Manual and product page.
NUX MG-30Line 6 POD Go
Amp models35: 28 electric, 2 acoustic and 5 bass107 guitar and bass amps and preamps
NAM captures10 NAM slots in the AMP block, with the GEN2 firmwareNot in Line 6's 2.50 manual
CabsBuilt-in cab IRs from NUX's Solid Studio, plus 8 bass and 3 acoustic IRs46 cab models
Third-party IRsOne per patch, 128 in all, at 1024 samplesUp to 128, shortened or lengthened to 1,024 samples
Blocks in a preset11 movable signal blocks, with parallel post-effects routingSix fixed blocks plus up to four effects blocks of your choice
Presets128 patches, 01A to 32D256, in two setlists of 128
Switching within a preset3 scenes; Pro Scene can change amp and effects models4 snapshots, recalling every block's bypass state and up to 64 parameter settings
FootswitchesUP, DOWN and CTRL, plus the NMP-2 LITE dual footswitch in the boxFS1 to FS6, TAP and MODE
Expression pedalBuilt in, plus an EXP1 jackBuilt in, with a toe switch for Wah and Volume, plus an EXP 2 jack
Screen4-inch colour LCD4.3-inch (11 cm) colour LCD
Looper60 seconds mono or 30 seconds stereo40 seconds mono or 20 seconds stereo, double at half speed
DrumsDrum styles with the looperNot in Line 6's manual
OutputsL and R, a 1/8-inch phones jack, Send and ReturnMain Out L/Mono and Right, Amp Out, Phones and a stereo FX Loop
Into a guitar ampOutput modes that bypass the cab IR on the main outputsAmp Out, which can be tapped before the Cab/IR block
USBAudio interface, with ReAmp, NORMAL and Dry Out routingMultichannel 24-bit audio interface with DI and re-amping
Power9 V DC, negative centre, under 400 mALine 6's supplied DC-3 power supply

Amp models and captures

The POD Go draws its amp, cab and effect models from Line 6's HX family of processors. Its amp list has 107 guitar and bass models, most based on a named amp, and each preset runs one of them as an Amp block, preamp and power amp, or a Preamp block, preamp only. The cab list has 46 models, and up to 128 third-party IRs sit beside them.

NUX went the other way. Its MG-30 page says working musicians don't need hundreds of mediocre amp models, so it focused on 35: 28 electric guitar amps, 2 acoustic and 5 bass, with a Bias parameter on the valve amp models to adjust the warmth of the sound. The GEN2 firmware adds a NAM loader with 10 slots in the AMP block, so NAM captures can sit alongside them. Every patch can also load one third-party IR, 128 in all.

Building a preset

Line 6 calls the POD Go's signal path semi-fixed. Every preset holds one amp or preamp block, one cab or IR block, a Wah, a Volume pedal, a Preset EQ and an FX Loop, and up to four more effects blocks of your choice; a model greyed out in the list means there is not enough processing left for it.

The MG-30 has 11 movable signal blocks. Holding two block buttons swaps their positions, with the AMP and IR blocks fixed together, and the routing screen can set the post effects, modulation, delay and reverb, to run in parallel. NUX's manual adds a hidden exchange that lets CMP and two EFX drives run at the same time.

On stage: snapshots, scenes and footswitches

The POD Go has six footswitches below the screen plus TAP and MODE. In Stomp mode, FS1 to FS6 turn their blocks on and off like a pedalboard; in Preset mode, A to D pick presets. Each preset has four snapshots, which Line 6 calls almost presets within a preset: they recall every block's bypass state and up to 64 parameter settings, and a delay or reverb with Trails On keeps ringing across the change.

The MG-30 has three footswitches, UP, DOWN and CTRL, and ships with the NMP-2 LITE dual footswitch for its EXP1 jack. Assign CTRL to SCENE and it steps through S1, S2 and S3. NUX's page says the V5 firmware's Pro Scene can change effects models, amp models and settings within the same preset, and answers why there is no Stomp Mode: the NMP-2 LITE and CTRL work three signal blocks as stomps.

Match a song to my amp7 days free, $0 today

Into an amp, a PA or a computer

For a guitar amp, the POD Go has its own Amp Out, which echoes the main outputs and can be set to tap off just before the Cab/IR block, so the amp gets no cab while the main outputs still feed a mixer. The MG-30 does the same job on its main outputs: NUX's manual says COMBO FRONT and STACK FRONT bypass the IR block; COMBO REAR and STACK REAR are the modes for an amp's effects loop return. Both have a send and return loop for the 4-cable method.

Both record to a computer over USB. Line 6 calls the POD Go a multichannel, 24-bit audio interface with DI and re-amping built in. The MG-30's USB routing offers ReAmp, NORMAL and Dry Out, and NUX publishes ASIO drivers for Windows and suggests an I/O buffer of 128 samples.

For practice, the MG-30's looper records 60 seconds in mono or 30 in stereo, with drum styles and a drum tempo beside it. The POD Go's looper records 40 seconds in mono or 20 in stereo, doubled at half speed.

The same starting points on both

These are Tonelify's starting settings from each unit's gear page, not NUX's or Line 6's numbers. The MG-30's amp knobs run 0 to 100, the range NUX's MIDI chart gives them; the POD Go's values are as POD Go shows them, 0 to 10. The amp models differ too, so each cell names the model its values are for.

Tonelify starting points from the MG-30 and POD Go gear pages. Move one control at a time from here.
SoundMG-30POD Go
CleanJAZZ CLEAN, Gain 20, Master 50, Bass 50, Middle 50, Treble 60US Deluxe Nrm, Drive 3.0, Bass 5.0, Mid 5.5, Treble 6.0, Presence 3.0
BluesDELUXE RVB, Gain 45, Master 60, Bass 45, Middle 55, Treble 55Tweed Blues Brt, Drive 4.5, Bass 4.0, Mid 6.0, Treble 5.5, Sag 6.0
Classic rockPLEXI 100W, Gain 60, Master 55, Bass 50, Middle 65, Treble 60, Presence 50Brit Plexi Jump, Drive 6.0, Bass 4.5, Mid 6.5, Treble 6.0, Presence 5.0
MetalDUAL RECT, Gain 70, Master 50, Bass 55, Middle 45, Treble 60, Presence 55PV Panama, Drive 5.5, Bass 5.0, Mid 5.0, Treble 6.0, Sag 3.0
LeadSLO 100, Gain 65, Master 50, Bass 50, Middle 65, Treble 55, Presence 50Solo Lead OD, Drive 6.5, Bass 4.5, Mid 6.5, Treble 5.5, Presence 5.0

Settings for a song, on either unit

A style setting gets you close. A particular record needs its own numbers, and they land differently on an MG-30 amp model than on a POD Go one. Tonelify gives song settings for the controls each of these units actually has, so the answer for one is never a copy of the other.

Common questions

Which has more amp models, the MG-30 or the POD Go?

The POD Go: Line 6's amp list has 107 guitar and bass amps and preamps, drawn from its HX family. NUX's MG-30 page counts 35, 28 electric, 2 acoustic and 5 bass, and says NUX chose to focus on 35 classic essentials rather than hundreds; the GEN2 firmware adds 10 NAM slots to the AMP block.

Can the POD Go load NAM captures like the MG-30?

Line 6's 2.50 Owner's Manual for the POD Go describes no NAM loader; outside its own models, it takes up to 128 third-party IRs in the Cab/IR block. The MG-30's 10 NAM slots came with NUX's GEN2 firmware, which NUX says works only with the GEN2 QuickTone editor.

Which is better for switching sounds within a song?

Both do it inside one preset. The POD Go has four snapshots per preset, chosen with A to D in Snapshot mode, each recalling every block's bypass state and up to 64 parameter settings. The MG-30 has three scenes, stepped through with the CTRL footswitch, and NUX says its Pro Scene can also change amp and effects models. Line 6 says POD Go snapshots can't swap out an effect or amp for a different one.

Which has the longer looper, the MG-30 or the POD Go?

The MG-30: 60 seconds in mono or 30 in stereo, on Aria's parameter sheet. The POD Go records 40 seconds in mono or 20 in stereo, and 80 or 40 at half speed. The MG-30 also has drum styles to play along with; Line 6's manual lists none for the POD Go.

Can you use both with a tube amp?

Yes. The POD Go has an Amp Out for the front of the amp, which can be tapped before the Cab/IR block, and its FX Loop runs the 4-cable method. The MG-30 uses its output modes: COMBO FRONT or STACK FRONT bypass the IR block for the amp's input, the two rear modes are for the amp's effects loop return, and its Send and Return can sit at any position in the chain for the 4-cable method.

Can both record to a computer?

Yes, over USB. Line 6 calls the POD Go a multichannel, 24-bit audio interface with DI and re-amping built in. The MG-30's USB routing offers ReAmp, NORMAL and Dry Out, and NUX publishes ASIO drivers for Windows 7 and for Windows 10 and above.

Sources

Gear in this guide

Settings for your own amp

This guide covers what is true of every rig. For a specific song on a specific amp, Tonelify reads the documented chain behind the recording and returns gain, bass, middle, treble and presence values for the controls your amp actually has. A first plan starts with 7 days free, $0 today.

Keep reading