Gear compared
IK Multimedia TONEX Pedal vs TONEX ONE
Updated 6 min read3 sources
Both play the same Tone Models with the same effects: a noise gate, a compressor, 5 modulations, 2 delays and 6 reverbs. The TONEX Pedal is the floor unit, 176 by 142 by 55 mm and 906 grams, with a display, three footswitches, five knobs, up to 150 presets in 50 banks, a separate headphones output, MIDI ports and an expression pedal input. The TONEX ONE is a mini pedal, 48 by 94 by 53 mm and 160 grams, with one footswitch, no display, a main knob and three micro knobs, and 20 presets, three of them in play.
Choose the TONEX Pedal to switch among many sounds on stage and edit every setting on the unit. Choose the TONEX ONE for one amp or drive sound on a crowded pedalboard, with the deeper settings made in TONEX software. Every figure on this page comes from IK Multimedia's own manuals.

Side by side
Both columns are from IK Multimedia's user manuals, the TONEX Pedal User Manual and the TONEX ONE User Manual, version 1.3.0. Where a manual does not list a feature, the cell says so rather than guessing.
| TONEX Pedal | TONEX ONE | |
|---|---|---|
| Size | 176 wide, 142 deep, 55 high, in mm | 48 wide, 94 deep, 53 high, in mm |
| Weight | 906 grams | 160 grams |
| Footswitches | Three: A, B and C | One |
| Display | Main display and a colour-coded sub-display | None; LEDs show the mode and the preset |
| Knobs | Five: Gain, Bass, Mid, Treble and Volume, plus three encoders | A main knob for Volume and three micro knobs for Bass, Mid and Treble |
| Second layer | Reverb, compressor, noise gate, Presence and Depth | Gain, noise gate, compressor and reverb |
| Presets | Up to 150, in 50 banks of three, holding up to 300 Tone Models | 20, assignable to 3 playable active slots |
| Effects | Noise gate, compressor, 5 modulations, 2 delays and 6 reverbs | Noise gate, compressor, 5 modulations, 2 delays and 6 reverbs |
| Editing effects | On the pedal, in the menus under the PARAMETER encoder | Gate, compressor and reverb mix on the pedal; the rest only in TONEX software |
| Saving | Hold the PRESET encoder; the display shows SAVED | Automatic, in real time |
| Outputs | Stereo outputs; the left alone for mono | One jack, mono or stereo |
| Headphones | Own output, a copy of the main output | From the output jack |
| MIDI | MIDI ports | None; the TONEX ONE+ adds it |
| Expression or switch | EXT. CONTROL socket | None |
| USB | Audio interface; USB OUT sends stereo, or processed plus dry DI | 24-bit, 44.1 kHz audio interface, which can also power the pedal |
| Power | 9 V DC, centre negative, 320 mA | 9 V DC, centre negative, 120 mA, or 5 V at 260 mA over USB-C |
| Software included | TONEX for Mac/PC and AmpliTube 5 | TONEX for Mac/PC SE and AmpliTube 5 SE |
Same Tone Models, different controls
A Tone Model, IK's capture of an amp, a pedal or both, plays the same on either unit, and IK's TONEX ONE manual shows a ONE used as the stomp in front of a TONEX Pedal used as the amp. Both shape it with Gain, Bass, Mid and Treble: Bass and Treble are shelf EQs and Mid a bell EQ in both manuals.
On the TONEX Pedal each of Gain, Bass, Mid, Treble and Volume has its own knob, and holding the PARAMETER encoder turns the same five into reverb, compressor, noise gate, Presence and Depth. Volume there is the pedal's master: IK says it is persistent across all the presets. On the TONEX ONE the main knob is the preset's volume and the micro knobs are Bass, Mid and Treble; press ALT and they become Gain, noise gate, compressor and reverb. Presence, Depth and the other additional parameters are set in TONEX software and carried in the preset: IK says they cannot be accessed on the TONEX ONE itself.
Presets on stage
The TONEX Pedal holds up to 150 presets in 50 banks of three. Each footswitch loads its preset, A and B together move a bank down, and B and C together move a bank up. Holding the PRESET encoder saves the current preset, and the display shows SAVED.
The TONEX ONE holds 20 presets and plays three: preset A and preset B in dual mode, where the footswitch flips between them and there is no bypass, and one in stomp mode, where the footswitch turns it on and off. Pressing ALT and the footswitch together opens browsing mode to assign the three slots, and IK's tip for three sounds on stage is to leave browsing mode on and let the footswitch cycle them. There is no save step: the ONE saves every change to the current preset in real time.
Outputs, headphones and recording
The TONEX Pedal has stereo outputs, with the left one alone for a mono setup, and a headphones output that IK describes as a copy of the main output. Its MIDI ports and its EXT. CONTROL socket, for a single switch, a double switch or an expression pedal, have no counterpart on the ONE. Over USB it is an audio interface, and its USB OUT setting sends either the processed stereo signal or the left processed signal on output 1 with the dry DI signal on output 2.
The TONEX ONE has one output jack, mono or stereo, which IK says can feed other pedals, a PA through a DI, an amplifier, an FRFR cabinet, headphones or studio monitors; a Y cable splits it for stereo. Over USB-C it is a 24-bit, 44.1 kHz audio interface, and IK notes that it can be powered from that port when connected to a computer. The TONEX ONE+ adds a MIDI input and output on a 1/8-inch TRS Type A jack.
The same starting points on both
These are Tonelify's starting settings from each unit's gear page, not IK's numbers, on a 0 to 10 scale: the TONEX Pedal's own display, and TONEX Editor's scale for the TONEX ONE. They match because both run the same Tone Models with the same four tone controls; what changes is where you turn them. On the ONE, Gain sits under ALT on the main knob.
| Sound | TONEX Pedal | TONEX ONE |
|---|---|---|
| Clean | Clean Tone Model, Gain 3 to 4, Bass 5, Mid 5, Treble 6 | Clean Tone Model, Gain 3 to 4, Bass 5, Mid 5, Treble 6 |
| Blues | Clean or crunch Tone Model, Gain 5 to 6, Bass 4 to 5, Mid 6, Treble 5 | Clean or crunch Tone Model, Gain 5 to 6, Bass 4 to 5, Mid 6, Treble 5 |
| Classic rock | Drive Tone Model, Gain 5 to 6, Bass 5, Mid 6 to 7, Treble 6 | Drive Tone Model, Gain 5 to 6, Bass 5, Mid 6 to 7, Treble 6 |
| Metal | High-gain Tone Model, Gain 4 to 5, Bass 4 to 5, Mid 5 to 6, Treble 6 | High-gain Tone Model, Gain 4 to 5, Bass 4 to 5, Mid 5 to 6, Treble 6 |
| Drive pedal | Stomp Tone Model, cab bypassed, Gain 3 to 4, Bass 5, Mid 6, Treble 5 | Stomp Tone Model, stomp mode, Gain 3 to 4, Bass 5, Mid 6, Treble 5 |
Settings for a song, on either unit
A style setting gets you close. A particular record needs its own numbers, and on these two the first of them is which Tone Model to load. Tonelify gives song settings for the controls each unit actually has, so the answer for one is never a copy of the other.
Common questions
Do the TONEX Pedal and TONEX ONE sound the same?
They play the same Tone Models with the same effects, and IK gives both the same 24-bit/192 kHz converters, 5 Hz to 24 kHz frequency response and up to 123 dB of dynamic range. The differences IK lists are in the controls, the number of presets and the connections.
Can the TONEX ONE use the same Tone Models as the TONEX Pedal?
Yes. IK's manual says you can play all the Tone Models available in TONEX Pedal, TONEX ONE and TONEX for Mac/PC, plus the ones other users share on ToneNET, and it shows a TONEX ONE used as a stomp in front of a TONEX Pedal used as the amp.
Which has more presets, the TONEX Pedal or the TONEX ONE?
The TONEX Pedal: up to 150 presets in 50 banks of three, and up to 300 stored Tone Models. The TONEX ONE has 20 presets, three of them assigned to its active slots: preset A and preset B in dual mode, and one in stomp mode.
Does the TONEX ONE have MIDI or an expression pedal input?
No. IK's TONEX ONE manual lists neither; the TONEX ONE+ adds a MIDI input and output on a 1/8-inch TRS Type A jack. The TONEX Pedal has MIDI ports and an EXT. CONTROL socket for a single switch, a double switch or an expression pedal.
Can you use headphones with both?
Yes. The TONEX Pedal has its own headphones output, a copy of the main output. The TONEX ONE has one output jack, which IK says can feed headphones among other things. IK says to keep the cab section on for headphones on either.
What power supply do the TONEX Pedal and TONEX ONE need?
Both take 9 V DC, centre negative: 320 mA for the TONEX Pedal and 120 mA for the TONEX ONE, which can also run from its USB-C port at 5 V and 260 mA. Check that a pedalboard supply's output can deliver the TONEX Pedal's 320 mA.
Do you need a computer for the TONEX ONE?
To reach everything, yes: IK says the ONE's additional parameters, such as the modulation, delay and reverb type, cannot be accessed on the pedal, only in TONEX software. The pedal itself sets Volume, Bass, Mid, Treble, Gain, the noise gate, the compressor and the reverb mix. The TONEX Pedal shows all its parameters in its own menus in Advanced user mode.
Sources
Gear in this guide
Settings for your own amp
This guide covers what is true of every rig. For a specific song on a specific amp, Tonelify reads the documented chain behind the recording and returns gain, bass, middle, treble and presence values for the controls your amp actually has. A first plan starts with 7 days free, $0 today.


