Line 6 POD Go presets and settings
Floor modeller with eight footswitches and a treadle. Six fixed blocks (wah, volume, FX loop, amp, cab and EQ) plus four free ones per preset.
⚡ Match a tone on this unitHow do you dial in a specific tone on a Line 6 POD Go?
A multi-effects unit gives you the whole chain in one box, which means the order of the blocks is as much of the answer as the values inside them. Settings for the Line 6 POD Go name the amp model, the block order and the parameters together, rather than handing you numbers with no chain to put them in.
Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact multi-effects unit, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.

Free download
Printable cheat sheet: PDF and PNG
The clean, blues, classic rock, metal and lead settings from this page, together on one sheet with short tips. The PDF prints on white; the PNG is the dark version for your phone.
Starting settings on the Line 6 POD Go
Values as the unit's screen shows them, on its own scale; each drawn knob shows that value's share of the range. They are where to begin, not Line 6's numbers: pick the amp model first, then move one control at a time from here.
Clean
US Deluxe Nrm, which Line 6 bases on the normal channel of a Fender Deluxe Reverb, and the amp POD Go Edit's guide shows in its picture of the editor. Drive 3.0, Bass 5.0, Mid 5.5, Treble 6.0, Presence 3.0. Keep Drive low for the clean and set the loudness with the Output block's Level, which Line 6 says sets the overall level of the entire preset. Line 6 describes Master as setting both the amp's output level and its power amp distortion: the lower it sits, the less the other power amp controls do. US Double Nrm, based on the Twin Reverb's normal channel, is the other Fender clean, and Jazz Rivet 120, based on the Roland JC-120 Jazz Chorus, a third.
- Drive 3.0
- Bass 5.0
- Mid 5.5
- Treble 6.0
- Presence 3.0
Edge of breakup and blues
Tweed Blues Brt, which Line 6 bases on the bright channel of a Fender Bassman. Drive 4.5, Bass 4.0, Mid 6.0, Treble 5.5, Sag 6.0, a setting that sits between clean and breaking up. Line 6's manual says higher Sag values give more touch dynamics and sustain for blues and classic rock riffs, so Sag is turned up here. For more push, put Minotaur, Line 6's model of the Klon Centaur, in a free block before the amp with its gain low. 4x10 Tweed P10R, which Line 6 captured from a 4x10 Fender Bassman with P10R speakers, is the cab to pair with it.
- Drive 4.5
- Bass 4.0
- Mid 6.0
- Treble 5.5
- Sag 6.0
Sag up for touch dynamics, Minotaur before the amp for more push.
Classic rock
Brit Plexi Jump, which Line 6 bases on a Marshall Super Lead 100 with its channels jumped. Drive 6.0, Bass 4.5, Mid 6.5, Treble 6.0, Presence 5.0. Keep the Mid up: in a band mix, rock rhythm guitar sits in the mids, and cutting them is what makes a preset vanish behind the drums. Line 6 says Bias X decides how the power tubes react when pushed hard, set low for a tighter feel and high for more tube compression, and that it reacts strongly with Drive and Master. For more gain, Scream 808, Line 6's model of the Ibanez TS808 Tube Screamer, goes in front with its gain low. 4x12 Greenback25, captured from a 4x12 Marshall Basketweave with G12 M25 speakers, suits it.
- Drive 6.0
- Bass 4.5
- Mid 6.5
- Treble 6.0
- Presence 5.0
Scream 808 in front, its gain low, for more drive.
Metal
PV Panama, which Line 6 bases on the Peavey 5150. Drive 5.5, Bass 5.0, Mid 5.0, Treble 6.0, Sag 3.0. Line 6's manual says lower Sag values give a tighter response for faster metal playing, and that Bias X set low gives a tighter feel. Turn on the gate in the Input block and raise its Threshold only until the hiss between chords stops; if your guitar gets cut off abruptly, Line 6 says, turn the Threshold down. Scream 808 in front with its gain low tightens palm mutes, and 4x12 Cali V30, captured from a MESA/Boogie 4FB with Vintage 30 speakers, is a cab to start from.
- Drive 5.5
- Bass 5.0
- Mid 5.0
- Treble 6.0
- Sag 3.0
Sag down, and the gate on in the Input block.
Lead
Solo Lead OD, which Line 6 bases on the overdrive channel of a Soldano SLO-100. Drive 6.5, Bass 4.5, Mid 6.5, Treble 5.5, Presence 5.0. Put a delay in a free block after the Cab and turn its Trails On: Line 6 says the repeats then keep decaying naturally when the block is bypassed or a different snapshot is selected. Transistor Tape, based on the Maestro Echoplex EP-3, and Elephant Man, based on the Electro-Harmonix Deluxe Memory Man, are two delays to start from. To keep the solo inside a rhythm preset, give it a snapshot of its own, or one footswitch: POD Go Edit's guide uses a solo as its example of several changes on one switch, a volume and gain boost on a distortion, more Mix on the delay and reverb and a chorus switched on.
- Drive 6.5
- Bass 4.5
- Mid 6.5
- Treble 5.5
- Presence 5.0
Delay after the Cab with Trails On, and a snapshot for the solo.
Snapshots and the four free blocks
Every POD Go preset holds the same six blocks: one Amp or Preamp, one Cab or IR, a Wah, a Volume pedal, a Preset EQ and an FX Loop, plus up to four effects blocks of your choice, placed anywhere in the chain. A model greyed out in the list means there is not enough DSP left for it; Line 6's example is that after three reverbs, a fourth probably will not fit. Distortion, Dynamics and Pitch/Synth models are all mono, so a distortion placed after a stereo delay or reverb folds the signal to mono there. Each preset also has four snapshots, which recall every block's on or off state, loopers aside, and up to 64 parameter settings at once, though they cannot swap one model for another. From Preset mode, press the bank Up and Down switches together for Snapshot mode, where A, B, C and D select snapshots 1 to 4. To change a knob per snapshot, press and turn it: the value turns white and appears in brackets. Saving the preset stores all four snapshots, and selecting it recalls the snapshot that was active when it was saved.
Chasing one song? Name it and the matcher writes that song's settings for the Line 6 POD Go.
Line 6 POD Go amp list
Every POD Go preset has one Amp or Preamp block: an Amp block models the preamp and the power amp, a Preamp block only the preamp. Line 6's table, below, has 107 guitar and bass models, 15 of them Line 6 Originals, its own designs, and Studio Tube Pre, a mic preamp, is in the Preamp list only. Changing the model loads a matching cab, unless Link Amp/Cab is turned off in Global Settings > Preferences.
| Model | What Line 6 says it is based on |
|---|---|
| WhoWatt 100 | Hiwatt DR-103 Brill |
| Soup Pro | Supro S6616 |
| Stone Age 185 | Gibson EH-185 |
| Voltage Queen | Victoria Electro King |
| Tweed Blues Nrm | Fender Bassman (normal channel) |
| Tweed Blues Brt | Fender Bassman (bright channel) |
| Fullerton Nrm | Fender 5C3 Tweed Deluxe (normal channel) |
| Fullerton Brt | Fender 5C3 Tweed Deluxe (bright channel) |
| Fullerton Jump | Fender 5C3 Tweed Deluxe (jumped) |
| GrammaticoLG Nrm | Grammatico LaGrange (normal channel) |
| GrammaticoLG Brt | Grammatico LaGrange (bright channel) |
| GrammaticoLGJump | Grammatico LaGrange (jumped) |
| US Small Tweed | Fender Champ |
| US Princess | Fender Princeton Reverb |
| US Super Nrm | Fender Super Reverb (normal channel) |
| US Super Vib | Fender Super Reverb (vibrato channel) |
| US Deluxe Nrm | Fender Deluxe Reverb (normal channel) |
| US Deluxe Vib | Fender Deluxe Reverb (vibrato channel) |
| US Double Nrm | Fender Twin Reverb (normal channel) |
| US Double Vib | Fender Twin Reverb (vibrato channel) |
| Mail Order Twin | Silvertone 1484 |
| Divided Duo | ÷13 JRT 9/15 |
| Interstate Zed | Dr Z Route 66 |
| Derailed Ingrid | Trainwreck Circuits Express |
| Grammatico GSG | Grammatico GSG100 |
| Jazz Rivet 120 | Roland JC-120 Jazz Chorus |
| Essex A15 | Vox AC-15 |
| Essex A30 | Vox AC-30 with top boost |
| A30 Fawn Nrm | Vox AC-30 Fawn (normal channel) |
| A30 Fawn Brt | Vox AC-30 Fawn (bright channel) |
| Matchstick Ch1 | Matchless DC30 (channel 1) |
| Matchstick Ch2 | Matchless DC30 (channel 2) |
| Matchstick Jump | Matchless DC30 (jumped) |
| Mandarin 80 | Orange OR80 |
| Mandarin Rocker | Orange Rockerverb 100 MkIII (dirty channel) |
| Moo)))n Nrm | Sunn Model T (normal channel) |
| Moo)))n Brt | Sunn Model T (brite channel) |
| Moo)))n Jump | Sunn Model T (jumped channels) |
| Brit J45 Nrm | Marshall JTM-45 (normal channel) |
| Brit J45 Brt | Marshall JTM-45 (bright channel) |
| Brit Trem Nrm | Marshall JTM-50 (normal channel) |
| Brit Trem Brt | Marshall JTM-50 (bright channel) |
| Brit Trem Jump | Marshall JTM-50 (jumped) |
| Brit Plexi Nrm | Marshall Super Lead 100 (normal channel) |
| Brit Plexi Brt | Marshall Super Lead 100 (bright channel) |
| Brit Plexi Jump | Marshall Super Lead 100 (jumped) |
| Brit P75 Nrm | Park 75 (normal channel) |
| Brit P75 Brt | Park 75 (bright channel) |
| Brit 2203 | Marshall JCM-800, 100W, 2203 |
| Brit 2204 | Marshall JCM-800, 50W, 2204 |
| Placater Clean | Friedman BE-100 (clean channel) |
| Placater Dirty | Friedman BE-100 (BE/HBE channel) |
| Cartographer | Ben Adrian Cartographer |
| German Xtra Blue | Bogner Ecstasy 101B, EL34 (blue channel) |
| German Xtra Red | Bogner Ecstasy 101B, EL34 (red channel) |
| German Mahadeva | Bogner Shiva |
| German Ubersonic | Bogner Überschall |
| Cali Texas Ch 1 | MESA/Boogie Lone Star (clean channel) |
| Cali Texas Ch 2 | MESA/Boogie Lone Star (drive channel) |
| Cali IV Rhythm 1 | MESA/Boogie Mark IV (channel I) |
| Cali IV Rhythm 2 | MESA/Boogie Mark IV (channel II) |
| Cali IV Lead | MESA/Boogie Mark IV (lead channel) |
| Cali Rectifire | MESA/Boogie Dual Rectifier |
| Archetype Clean | Paul Reed Smith Archon (clean channel) |
| Archetype Lead | Paul Reed Smith Archon (lead channel) |
| ANGL Meteor | ENGL Fireball 100 |
| Solo Lead Clean | Soldano SLO-100 (clean channel) |
| Solo Lead Crunch | Soldano SLO-100 (crunch channel) |
| Solo Lead OD | Soldano SLO-100 (overdrive channel) |
| PV Panama | Peavey 5150 |
| Revv Gen Purple | Revv Generator 120 (purple [gain 1] channel) |
| Revv Gen Red | Revv Generator 120 (red [gain 2] channel) |
| Das Benzin Mega | Diezel VH4 (mega channel) |
| Das Benzin Lead | Diezel VH4 (lead channel) |
| Line 6 Clarity | Line 6 Original |
| Line 6 Aristocrat | Line 6 Original |
| Line 6 Carillon | Line 6 Original |
| Line 6 Voltage | Line 6 Original |
| Line 6 Kinetic | Line 6 Original |
| Line 6 Oblivion | Line 6 Original |
| Line 6 Ventoux | Line 6 Original |
| Line 6 Elmsley | Line 6 Original |
| Line 6 Elektrik | Line 6 Original |
| Line 6 Doom | Line 6 Original |
| Line 6 Epic | Line 6 Original |
| Line 6 2204 Mod | Line 6 Original |
| Line 6 Fatality | Line 6 Original |
| Line 6 Litigator | Line 6 Original |
| Line 6 Badonk | Line 6 Original |
| Ampeg B-15NF | Ampeg B-15NF Portaflex |
| Ampeg SVT Nrm | Ampeg SVT (normal channel) |
| Ampeg SVT Brt | Ampeg SVT (bright channel) |
| Ampeg SVT-4PRO | Ampeg SVT-4 PRO |
| US Dripman Nrm | Fender Bassman (Silverface) |
| Woody Blue | Acoustic 360 |
| Agua Sledge | Aguilar Tone Hammer |
| Agua 51 | Aguilar DB51 |
| Mandarin Bass 200 | Orange AD200 MkIII |
| Cali Bass | MESA/Boogie M9 Carbine |
| Cali 400 Ch1 | MESA/Boogie Bass 400+ (channel 1) |
| Cali 400 Ch2 | MESA/Boogie Bass 400+ (channel 2) |
| G Cougar 800 | Gallien-Krueger GK 800RB |
| Del Sol 300 | Sunn Coliseum 300 |
| Busy One Ch1 | Pearce BC-1 preamp (channel 1) |
| Busy One Ch2 | Pearce BC-1 preamp (channel 2) |
| Busy One Jump | Pearce BC-1 preamp (jumped) |
| Studio Tube Pre | Requisite Y7 mic preamp (Preamp list only) |
Line 6 POD Go cab list
The Cab/IR block holds one cab model, or one of up to 128 impulse responses loaded with POD Go Edit. These are the 46 cabs of the Cab subcategory, which since firmware 2.00 run on a new cab engine that Line 6 says gives more accurate sonic detail and more mic positioning options. Each takes one of 12 guitar or 12 bass mic models, placed from the centre to the edge of the cone, 1 to 12 inches away, on axis or 45 degrees off it. The 41 cabs from before 2.00 are still there as Legacy Cabs, so older presets load with the cabs they were saved with.
| Cab | What Line 6 says it is captured from |
|---|---|
| Soup Pro Ellipse | 1x6×9" Supro, S6616 |
| 1x8 Small Tweed | 1x8" Fender Champ |
| 1x10 US Princess | 1x10" Fender Princeton Reverb |
| 1x12 Fullerton | 1x12" Fender 5C3 Tweed Deluxe |
| 1x12 Grammatico | 1x12" Grammatico LaGrange |
| 1x12 US Deluxe | 1x12" Fender Deluxe Oxford |
| 1x12 Open Cast | 1x12" Custom open-back, EVM12L |
| 1x12 Open Cream | 1x12" Custom open-back, G12M-65 |
| 1x12 Cali EXT | 1x12" MESA/Boogie Extension EVM12L |
| 1x12 Cali IV | 1x12" MESA/Boogie MkIV Combo |
| 1x12 Blue Bell | 1x12" Vox AC-15, Blue Alnico |
| 2x12 Blue Bell | 2x12" Vox AC-30 Fawn Blue |
| 2x12 Silver Bell | 2x12" Vox AC-30TB, Silver Alnico |
| 2x12 Match H30 | 2x12" Matchless DC30, Custom G12H-30 |
| 2x12 Match G25 | 2x12" Matchless DC30, Custom G12M-35 |
| 2x12 Double C12N | 2x12" Fender Twin C12N |
| 2x12 Interstate | 2x12" Dr. Z Z Best, V30 |
| 2x12 Jazz Rivet | 2x12" Roland JC-120 |
| 2x12 Mail C12Q | 2x12" Silvertone 1484, Jensen C12Q |
| 2x12 Mandarin30 | 2x12" Orange, Vintage 30 |
| 4x10 Tweed P10R | 4x10" Fender Bassman P10R |
| 4x10 US Super | 4x10" Fender Super Reverb, CTS alnico |
| 4x12 WhoWatt | 4x12" Hiwatt AP Fane |
| 4x12 Greenback20 | 4x12" Marshall Basketweave G12M-20 |
| 4x12 Greenback25 | 4x12" Marshall Basketweave G12 M25 |
| 4x12 Greenback30 | 4x12" Marshall Basketweave G12H-30 |
| 4x12 1960A T75 | 4x12" Marshall 1960A, G12T-75 |
| 4x12 Blackback30 | 4x12" Park 75, G12-H30 |
| 4x12 Brit V30 | 4x12" Marshall 1960AV, Vintage 30 |
| 4x12 Cali V30 | 4x12" MESA/Boogie 4FB, Vintage 30 |
| 4x12 Mandarin EM | 4x12" Orange, Eminence |
| 4x12 MOO)))N T75 | 4x12" Sunn, G12T-75 |
| 4x12 Cartog Guv | 4x12" Modified Lee Jackson, Eminence Governor |
| 4x12 Cartog C90 | 4x12" Modified Lee Jackson, Mesa C90 |
| 4x12 Uber T75 | 4x12" Bogner Uberkab, G12T-75 |
| 4x12 Uber V30 | 4x12" Bogner Uberkab, V30 |
| 4x12 XXL V30 | 4x12" ENGL XXL, V30 |
| 4x12 SoloLead EM | 4x12" Soldano, Eminence 12-5875 |
| 1x12 Epicenter | 1x12" Epifani Ultralight |
| 1x15 Ampeg B-15 | 1x15" Ampeg B-15 |
| 2x15 Brute | 2x15" MESA/Boogie 2x15 EV |
| 2x15 US Dripman | 2x15" Fender Bassman, JBL D130 |
| 4x10 Garden | 4x10" Eden D410XLT |
| 4x10 AmpegPro | 4x10" Ampeg PR-410HLF |
| 6x10 Cali Power | 6x10" MESA/Boogie PowerHouse |
| 8x10 SVT AV | 8x10" Ampeg SVT-810AV |
Line 6 POD Go effects list
A preset has four free effects blocks, and each can take any model from the nine categories below, Distortion to Looper; the Wah and Volume blocks have models of their own, listed last. Line 6 says POD Go has nearly all the effects of its HX family, plus selected effects from its older DL4, DM4, MM4 and FM4 stompboxes and M13, M9 and M5 processors: those legacy models are listed apart under each category. Where Line 6 names what a model is based on, it is in brackets; the rest are Line 6 Originals.
- Distortion (38)
- Kinky Boost (Xotic EP Booster), Deranged Master (Dallas Rangemaster Treble Booster), Minotaur (Klon Centaur), Teemah! (Paul Cochrane Timmy Overdrive), Heir Apparent (Analogman Prince of Tone), Alpaca Rouge (Way Huge Red Llama), Compulsive Drive (Fulltone OCD), Dhyana Drive (Hermida Zendrive), Horizon Drive (Horizon Precision Drive), Valve Driver (Chandler Tube Driver), Top Secret OD (DOD OD-250), Scream 808 (Ibanez TS808 Tube Screamer), Pillars (Earthquaker Devices Plumes), Hedgehog D9 (MAXON SD9 Sonic Distortion), Stupor OD (BOSS SD-1 Overdrive), Deez One Vintage (BOSS DS-1 Distortion, Made-in-Japan), Deez One Mod (BOSS DS-1 Distortion, Keeley modded), Ratatoullie Dist (Pro Co RAT, with LM308 opamp), Vermin Dist (Pro Co RAT), KWB (Benadrian Kowloon Walled Bunny Distortion), Swedish Chainsaw (Boss HM-2 Heavy Metal Distortion, MIJ), Arbitrator Fuzz (Arbiter Fuzz Face), Pocket Fuzz (Jordan Boss Tone Fuzz), Bighorn Fuzz ('73 Electro-Harmonix Ram's Head Big Muff Pi), Triangle Fuzz (Electro-Harmonix Big Muff Pi), Dark Dove Fuzz (Electro-Harmonix Russian Big Muff Pi), Ballistic Fuzz (Euthymia ICBM Fuzz), Industrial Fuzz (Z.Vex Fuzz Factory), Tycoctavia Fuzz (Tycobrahe Octavia), Wringer Fuzz (Garbage's modded BOSS FZ-2), Thrifter Fuzz, Xenomorph Fuzz (Subdecay Harmonic Antagonizer), Megaphone (a megaphone), Bitcrusher, Ampeg Scrambler (Ampeg Scrambler Bass Overdrive), ZeroAmp Bass DI (Tech 21 SansAmp Bass Driver DI V1), Regal Bass DI (Noble Preamp Bass DI), Obsidian 7000 (Darkglass Electronics Microtubes B7K Ultra)
- Distortion, legacy (17)
- Tube Drive (Chandler Tube Driver), Screamer (Ibanez Tube Screamer), Overdrive (DOD Overdrive/Preamp 250), Classic Dist (ProCo RAT), Heavy Dist (BOSS Metal Zone), Colordrive (Colorsound Overdriver), Buzz Saw (Maestro Fuzz Tone), Facial Fuzz (Arbiter Fuzz Face), Jumbo Fuzz (Vox Tone Bender), Fuzz Pi (Electro-Harmonix Big Muff Pi), Jet Fuzz (Roland Jet Phaser), L6 Drive (Colorsound Overdriver, modded), L6 Distortion, Sub Oct Fuzz (PAiA Roctave Divider), Octave Fuzz (Tycobrahe Octavia), Bronze Master (Maestro Bass Brassmaster), Killer Z (BOSS Metal Zone MT-2)
- Dynamics (11)
- Deluxe Comp, Red Squeeze (MXR Dyna Comp), Kinky Comp (Xotic SP Compressor), Ampeg Opto Comp (Ampeg Opto Comp Compressor), Rochester Comp (Ashly CLX-52, created in conjunction with Billy Sheehan), LA Studio Comp (Teletronix LA-2A), 3-Band Comp, Noise Gate, Hard Gate, Horizon Gate (the gate circuit of the Horizon Precision Drive), Autoswell
- Dynamics, legacy (7)
- Tube Comp (Teletronix LA-2A), Red Comp (MXR Dyna Comp), Blue Comp (BOSS CS-1), Blue Comp Treb (BOSS CS-1, Treble switch on), Vetta Comp, Vetta Juice, Boost Comp (MXR Micro Amp)
- EQ (8)
- Simple EQ, Low and High Cut, Low/High Shelf, Parametric, Tilt, 10 Band Graphic (MXR 10-Band Graphic EQ), Cali Q Graphic (MESA/Boogie Mark IV Graphic EQ), Acoustic Sim
- Modulation (29)
- Optical Trem (Fender optical tremolo circuit), 60s Bias Trem (Vox AC-15 Tremolo), Tremolo/Autopan (BOSS PN-2), Harmonic Tremolo, Bleat Chop Trem (Lightfoot Labs Goatkeeper), Script Mod Phase (MXR Phase 90), Pebble Phaser (Electro-Harmonix Small Stone phaser), Ubiquitous Vibe (Shin-ei Uni-Vibe), FlexoVibe, Deluxe Phaser, Gray Flanger (MXR 117 Flanger), Harmonic Flanger (A/DA Flanger), Courtesan Flange (Electro-Harmonix Deluxe EM), Dynamix Flanger (MicMix DynaFlanger), Chorus, 70s Chorus (BOSS CE-1), PlastiChorus (Modded Arion SCH-Z chorus), Ampeg Liquifier (Ampeg Liquifier Chorus), Trinity Chorus (Dytronics Tri-Stereo Chorus), 4-Voice Chorus, Bubble Vibrato (BOSS VB-2 Vibrato), Vibe Rotary (Fender Vibratone), 122 Rotary (Leslie 122), 145 Rotary (Leslie 145), Triple Rotary (Yamaha RA-200), Retro Reel, Double Take, AM Ring Mod, Pitch Ring Mod
- Modulation, legacy (26)
- Pattern Tremolo, Panner, Bias Tremolo (1960 Vox AC-15 Tremolo), Opto Tremolo (1964 Fender Deluxe Reverb), Script Phase (MXR Phase 90, script logo version), Panned Phaser (Ibanez Flying Pan), Barberpole, Dual Phaser (Mu-Tron Bi-Phase), U-Vibe (Shin-ei Uni-Vibe), Phaser (MXR Phase 90), Pitch Vibrato (BOSS VB-2), Dimension (Roland Dimension D), Analog Chorus (BOSS CE-1), Tri Chorus (Dytronics Tri-Stereo Chorus), Analog Flanger (MXR Flanger), Jet Flanger (A/DA Flanger), AC Flanger (MXR Flanger), 80A Flanger (A/DA Flanger), Frequency Shift, Ring Modulator, Rotary Drum (Fender Vibratone), Rotary Drum/Horn (Leslie 145), Tape Eater, Warble-Matic, Random S&H, Sweeper
- Delay (25)
- Simple Delay, Mod/Chorus Echo, Dual Delay, Multitap 4, Multitap 6, Ping Pong, Sweep Echo, Ducked Delay (TC Electronic 2290), Reverse Delay, Vintage Digital, Vintage Swell, Pitch Echo, Transistor Tape (Maestro Echoplex EP-3), Harmony Delay, Bucket Brigade (BOSS DM-2), Adriatic Delay (BOSS DM-2 w/ Adrian Mod), Adriatic Swell, Elephant Man (Electro-Harmonix Deluxe Memory Man), Multi Pass, Glitch Delay, Euclidean Delay, ADT, Crisscross, Tesselator, Ratchet
- Delay, legacy (17)
- Ping Pong Legacy, Dynamic (TC Electronic 2290), Stereo, Digital, Dig w/Mod, Reverse, Lo Res, Tube Echo (Maestro Echoplex EP-1), Tape Echo (Maestro Echoplex EP-3), Sweep Echo, Echo Platter (Binson EchoRec), Analog Echo (BOSS DM-2), Analog w/Mod (Electro-Harmonix Deluxe Memory Man), Auto-Volume Echo, Multi-Head (Roland RE-101 Space Echo), Bubble Echo, Phaze Eko
- Reverb (11)
- Dynamic Hall, Dynamic Plate, Dynamic Room, Dynamic Ambience, Shimmer, Hot Springs, Glitz, Ganymede, Searchlights, Plateaux, Double Tank
- Reverb, legacy (12)
- Plate, Room, Chamber, Hall, Echo, Tile, Cave, Ducking, Octo, '63 Spring, Spring, Particle Verb
- Pitch/Synth (7)
- Pitch Wham (Digitech Whammy), Twin Harmony (Eventide H3000), Simple Pitch, Dual Pitch, Boctaver (Boss OC-2 Octaver), 3 Note Generator, 4 OSC Generator
- Pitch/Synth, legacy (17)
- Bass Octaver (EBS OctaBass), Smart Harmony (Eventide H3000), Octi Synth, Synth O Matic, Attack Synth (Korg X911 Guitar Synth), Synth String (Roland GR700 Guitar Synth), Growler, Buzz Wave, Rez Synth, Seismik Synth, Analog Synth, Synth Lead, String Theory, Synth FX, Saturn 5 Ring Mod, Synth Harmony, Double Bass
- Filter (4)
- Mutant Filter (Musitronics Mu-Tron III), Mystery Filter (Korg A3), Autofilter, Asheville Pattrn (Moog Moogerfooger MF-105M MuRF Filter)
- Filter, legacy (11)
- Voice Box, V Tron (Musitronics Mu-Tron III), Q Filter, Seeker (Z Vex Seek Wah), Obi Wah (Oberheim voltage-controlled S&H filter), Tron Up (Musitronics Mu-Tron III, up position), Tron Down (Musitronics Mu-Tron III, down position), Throbber (Electrix Filter Factory), Slow Filter, Spin Cycle (Craig Anderton's Wah/Anti-Wah), Comet Trails
- Looper (4)
- 6 Sw Mono Looper, 1 Sw Mono Looper, 6 Sw Stereo Looper, 1 Sw Stereo Looper
- Wah (11)
- UK Wah 846 (Vox V846), Teardrop 310 (Dunlop Cry Baby Fasel model 310), Fassel (Dunlop Cry Baby Super), Weeper (Arbiter Cry Baby), Chrome (Vox V847), Chrome Custom (Modded Vox V847), Throaty (RMC Real McCoy 1), Vetta Wah, Colorful (Colorsound Wah-fuzz), Conductor (Maestro Boomerang), Teardrop Bass Q (Modified Dunlop 105Q)
- Volume/Pan (4)
- Volume Pedal, Gain, Pan, Stereo Width
Line 6 POD Go specifications
- Released
- 2020
Line 6 POD Go questions
What amps are in the Line 6 POD Go?
107 guitar and bass models in Line 6's Amp/Preamp table, drawn from its HX family of processors, as Line 6's POD Go page puts it. 15 are Line 6 Originals, its own designs; the others are based on real amps, from the Fender Bassman and the Marshall Super Lead 100 to the Peavey 5150 and the Diezel VH4, and the full list with what each is based on is below. Every preset has one Amp or Preamp block: Amp blocks model the preamp and the power amp, Preamp blocks only the preamp. All amps and preamps are mono.
How many effects can the POD Go run at once?
Up to four effects blocks of your choice, on top of the six blocks every preset has: Amp or Preamp, Cab or IR, Wah, Volume pedal, Preset EQ and FX Loop. Each of the four can be any model from nine categories, Distortion, Dynamics, EQ, Modulation, Delay, Reverb, Pitch/Synth, Filter and Looper, as long as there is DSP left: a model greyed out in the list will not fit, and Line 6's example is a fourth reverb after three. Only one Looper fits in a preset.
What is the difference between the POD Go and the POD Go Wireless?
The Wireless has a Line 6 Relay wireless receiver built in, ships with a Relay G10TII transmitter, charges the transmitter from its GUITAR IN jack and has a storage well for it in the back panel. Other than that, Line 6's manual says, they are pretty much identical. The G10TII's battery lasts for 7 hours of playing, and the line-of-sight range is up to 100 feet (30 metres). Choose Guitar+Wireless in the Input block to have the jack and the transmitter both active. Line 6 launched the POD Go Wireless on 10 March 2021 at $811.99 (MSRP).
How do you save a preset on the POD Go?
Press VIEW and ACTION together to open the Save menu, where you rename the preset and choose the setlist and location to save it to; press both buttons twice to quick save. POD Go has 256 preset locations, in two setlists of 128, Factory and User, and any of the 256 can be overwritten, not only those in the User setlist. To make a model load with your own settings every time, select its block, press ACTION and then Knob 4 (User Default): the screen flashes Saved as UMD!
How do snapshots work on the POD Go?
Line 6 calls them presets within a preset. Each preset has four, and each recalls the on or off state of every block except the Looper, the values of up to 64 parameters and, if Tempo Select is set to Per Snapshot, the tempo. From Preset footswitch mode, press the bank Up and Down switches together for Snapshot mode, then step on A to D for snapshots 1 to 4. Press and turn a knob to put its parameter under snapshot control. Turn the Trails parameter On in any delay, reverb or FX Loop block for spillover between snapshots. Saving the preset stores all four snapshots.
How do you use the POD Go with a tube amp?
Two ways, both in Line 6's manual. AMP OUT is meant for the front of your amp: by default it carries the same signal as the MAIN outputs, in mono, and setting Amp Out Source to Pre Cab/IR in Global Settings taps it off just before the Cab/IR block, so the cab and every block after it stay off the amp while the MAIN outputs still feed a mixer or FRFR speaker. With the 4-Cable Method, effects such as drives, wahs and compressors go before the amp's preamp and delays and reverbs into its effects loop: add a Send/Return > Mono FX Loop block where the amp's preamp should be, and bypass POD Go's Amp/Preamp and Cab/IR blocks. Line 6's tip is to put the FX Loop block (on) and a Preamp block (bypassed) on the same footswitch, to switch between the amp's preamp and a modelled one.
Can the POD Go be used as an audio interface?
Yes: Line 6 calls it a USB 2.0, multichannel, 24-bit, low-latency audio interface for Windows and Mac computers, and for iPad and iPhone with Apple's Camera Connection Kit. USB 1/2 carry the processed sound and USB 3/4 the dry GUITAR IN signal, for re-amping later; send a dry track back to USB 3/4, with the Input block set to USB 3/4, and it plays through POD Go. On Windows, install the Line 6 POD Go ASIO driver first. A Mac needs no driver, and Line 6's Mac Core Audio driver is only for sample rates other than 48 kHz. Use a USB 2.0 or 3.0 port, not a hub.
How do you set the noise gate on the POD Go?
In the Input block: knob 1 turns the gate on, knob 2 sets the Threshold, the level at which it acts, and knob 3 the Decay, how abruptly it closes once the signal drops below that level. If your guitar gets cut off abruptly, Line 6 says, turn the Threshold down. The Input block's settings are saved per preset. For more, the Dynamics category has Noise Gate and Hard Gate, both Line 6 Originals, and Horizon Gate, based on the gate circuit of the Horizon Precision Drive.
Can you load IRs into the POD Go?
Yes, up to 128 custom or third-party IRs at a time, imported with the free POD Go Edit application; each is shortened or lengthened to 1,024 samples on import. Choose IR in the Cab/IR block and pick one of the 128 with IR Select. Line 6 says the IR block's Level is normal at -18.0dB. A preset has one Cab/IR block and a block holds one model, so a preset runs either an IR or a cab model.
How do you update the POD Go's firmware?
With POD Go Edit on a Mac or Windows computer: if a newer firmware version is available for POD Go or a Relay G10T or G10TII transmitter, POD Go Edit walks you through the update. Line 6 says to back up first, because presets saved after an update may not load correctly in older POD Go Edit or firmware versions. This page follows the manual for firmware 2.50.
How do the POD Go's footswitches work?
MODE switches between Stomp and Preset footswitch modes. In Stomp mode, which Line 6 says is where you will spend most of your time, FS1 to FS6 turn their blocks on and off like a pedalboard, and pressing and holding two switches swaps all their assignments. Preset mode moves through presets in the current setlist with A to D. Press TAP two or more times to set the tempo; hold it for one second for the tuner, which mutes or bypasses the signal while you tune and takes a reference from 425 to 455 Hz. The EXP 2/FS 7/8 jack takes a second expression pedal or momentary footswitches, two on a Y cable (FS7 on the tip, FS8 on the ring).
Why does my POD Go show different knobs from these settings?
Because the amp models differ. Line 6's manual says the tone stack and the deeper amp parameters on the later pages may differ depending on the amp model selected, so a model without one of the knobs here skips it. The common amp settings Line 6 lists are Master, Sag, Hum, Ripple, Bias and Bias X. The values on this page are for the models named, as POD Go and POD Go Edit show them.
How long can the POD Go looper record?
40 seconds in mono, or 80 at half speed, and 20 seconds in stereo, or 40 at half speed. The Looper takes one of the four free effects blocks, one per preset, as a 6 Switch Looper, which opens a Looper mode on the footswitches, or a 1 Switch Looper run from one switch, each in mono or stereo. Recording at half speed doubles the memory; switch to full speed and the loop plays an octave up. You can change presets while looping, but playback stops unless the new preset has the same type of looper block.
What are the best Line 6 POD Go settings for metal?
Start with PV Panama, based on the Peavey 5150, at Drive 5.5, Bass 5.0, Mid 5.0, Treble 6.0 and Sag 3.0, with the Input block's gate on and Scream 808 in front with its gain low. These are starting points rather than Line 6's numbers. Line 6 ties lower Sag values to a tighter response for faster metal playing, and Bias X set low to a tighter feel; 4x12 Cali V30 is a cab to start from.
When did the Line 6 POD Go come out?
Line 6 introduced it on 18 January 2020, at $629.99 (MSRP), to be available worldwide in spring 2020. The POD Go Wireless, with a Relay wireless receiver built in, followed on 10 March 2021 at $811.99.
How do you build a patch on the Line 6 POD Go?
Pick the amp model first, then set its controls, then add the blocks in signal-chain order: drive before the amp, time and modulation after it. A patch built the other way around ends up compensating for the wrong stage. Tonelify returns the model, the order and the parameters together.
Does Tonelify support the Line 6 POD Go?
Yes. Name it in the tone matcher along with the song you are chasing and the settings come back adapted to it. Gear does not need to be in the catalog for a match to run.
Sources
Panel, specifications and dates checked against these on .
- Line 6: POD Go 2.50 Owner's Manual (PDF)
- Line 6: POD Go Edit 2.50 Pilot's Guide (PDF)
- Line 6: POD Go and POD Go Wireless
- Premier Guitar: Line 6 Debuts the POD Go Guitar Processor, Line 6's press release of 18 January 2020
- Premier Guitar: Line 6 Launches the POD Go Wireless, Line 6's press release of 10 March 2021
More Line 6 gear
Similar multi-effects units from other makers
Settings for the song you are chasing
Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the Line 6 POD Go in it. A first plan starts with 7 days free, $0 today.