Tonelify
Black Friday40% off yearly

Tone matching

Neural Amp Modeler and NAM A2: what it is, settings and what runs it

Updated 9 min read12 sources

Neural Amp Modeler (NAM) is free, open-source software that learns a real amp, pedal or rig from recordings and plays it back as a capture file. NAM A2 is its second architecture, launched on 2 June 2026 by TONE3000 with NAM's creator Steve Atkinson. One A2 model runs in two sizes: A2-Full for computers, which TONE3000 says uses 30 to 40% less CPU than the first architecture, and A2-Lite for pedals, which it says runs at 50% CPU on a $3 ARM Cortex-M7 chip.

To play one in the free TONE3000 plugin, plug into an instrument input and raise the interface gain until your hardest playing never clips. Load an Amp + Cab capture, since an Amp Head capture needs a cabinet IR, set Input and Output on the block, and drop the buffer to 128 samples if you hear a delay. Leave Normalize on, and turn on Calibration when you want a capture to respond the way its creator recorded it.

Match a song to my amp7 days free, $0 today
A power tube standing in front of two others, out of focus

What is Neural Amp Modeler?

Neural Amp Modeler is a way to copy the sound of a piece of gear by recording it rather than by programming its circuit. A sweep signal is sent through the amp or pedal, the dry input and the recorded output are captured together, and a neural network is trained on the pair until it predicts the output for any input. TONE3000 says the training typically takes 5 to 20 minutes.[3] The result is a capture, also called a NAM profile, model or file.

NAM launched as an open-source project in 2019. Its first architecture, A1, was designed by Steve Atkinson to run inside recording software on a computer, not on a pedal.[1]

A capture models the amp, the preamp or the pedal. The speaker cabinet is usually a separate impulse response (IR). A capture labelled Amp Head needs a cabinet IR after it, or it sounds thin and harsh; one labelled Amp + Cab already includes the cabinet, which is why TONE3000 tells beginners to start there.[3]

What is NAM A2?

A2 is the second architecture of Neural Amp Modeler, built by TONE3000 in partnership with Steve Atkinson over six months and launched on 2 June 2026.[1] It replaced A1 as the default for every new capture on TONE3000. The aims were better accuracy and enough efficiency to run on the small chips inside budget multi-effects pedals.

An A2 download is a single model that runs at either of two sizes. A2-Full is the maximum-accuracy version for computers and devices with processing to spare. A2-Lite is the same model at a smaller size for pedals and small amps, and the device often picks the size by itself.[2] A2-Nano, a name in early posts, is the same thing as A2-Lite.

A2 is MIT-licensed: the architecture, the training code and the inference engine are free to use and to ship in commercial products. TONE3000 says its receptive field, the stretch of recent signal it looks at, is about 50 percent longer than A1's, which lets it model sag and compression better.[2]

NAM architectures as TONE3000 describes them
ArchitectureBuilt forEfficiency, per TONE3000
A1-StandardRecording software on a computerThe baseline the others are measured against
A2-FullComputers and devices with processing to spare30 to 40% less CPU than A1-Standard: three A2-Full models for the CPU of two A1
A2-LitePedals, multi-effects units and small amps50% CPU on a $3 ARM Cortex-M7 600MHz chip

How accurate is NAM A2?

By TONE3000's own tests, more accurate than the commercial capture systems it compared. It scored models of 39 tones against recordings of the real gear, and ran a blind listening test in which over 1,000 participants gave more than 100,000 ratings. TONE3000 reports that A2-Full beat Neural DSP's Neural Capture V2, IK Multimedia's ToneX and Line 6's Proxy in both, and that A2-Lite beat them too. The tests were run in March 2026.[2]

Against its own first architecture, TONE3000 says the median error (ESR) roughly halved when it retrained its library, from 0.0062 with A1-Standard to 0.0033 with A2-Full.[2] These are the maker's figures for its own technology, so read them as such.

Neural Amp Modeler settings: getting the signal in

These are the settings in the free TONE3000 plugin, which plays NAM captures and IRs on its own or inside recording software. Plug the guitar into a Hi-Z or instrument input, with the interface's Line/Inst switch on Inst. Turn the interface gain up while playing as hard as you ever will, and stop below the point where the red clip light comes on.

Load an Amp + Cab capture, or an Amp Head followed by a cabinet IR. A pack can hold several models, each a different knob snapshot of the same gear,[4] so pick the one nearest the gain you want. Then set Input and Output on the block's faceplate.

If you hear a delay between the note and the sound, lower the buffer size to 128 samples,[4] in the standalone app's System Settings or in your recording software's audio preferences.

Input calibration and normalization

NAM captures are recorded at a known input level. Calibration tells the plugin how hot your interface's input is, so the capture is hit as hard as its creator hit the real amp, which matters most for feel and for how hard the virtual valves are driven. Turn it on in Plugin Settings and enter the dBu level that matches your recording software's maximum digital level: TONE3000 gives +12 dBu as typical for pro gear and +4 dBu for semi-pro.[4] Captures that carry calibration data show a gauge icon and use it by default.

Normalization is on for every capture as it loads. It levels each block's output so the volume stays the same when you swap models. TONE3000's advice for beginners is to leave Normalize on and skip calibration until you want to match a particular capture's feel.[4]

Match a song to my amp7 days free, $0 today

Noise gate settings for high-gain captures

The plugin's gate sits at the start of the chain and listens to a filtered copy of the input, roughly 80 Hz to 5 kHz, so hum does not hold it open. The Gate knob sets the threshold. The advanced controls are Release, how fast it closes, from 5 to 500 ms with 50 ms as the default; Hold, how long it stays open after the signal drops, from 0 to 200 ms with 20 ms as the default; and Range, how deep it closes, from 20 to 80 dB with 80 dB, fully muted, as the default.

For a tight rhythm part, TONE3000's tip is to raise the threshold until the noise between notes disappears, then shorten Release so the gate snaps shut.[4]

The TONE3000 plugin's settings that change how a NAM capture plays, with its defaults
SettingWhat it doesWhere to start
Interface gainSets the level into the pluginAs high as it goes without clipping on your hardest playing
Buffer sizeSets the delay between note and sound128 samples if you hear a delay
NormalizeKeeps each block at the same loudnessOn, the default
CalibrationMatches your input level to the capture'sOff until you want a capture's exact feel, then +12 dBu (pro) or +4 dBu (semi-pro)
Gate ReleaseHow fast the gate closes50 ms default, shorter for tight rhythm
Gate HoldHow long the gate stays open20 ms default
Gate RangeHow far the gate turns the sound down80 dB default, fully muted

Why a NAM capture does not have working amp knobs

A capture is a snapshot of the gear at one setting. Gearnews puts it this way: with NAM you get an extremely accurate sonic photograph, but when you change the knobs the result is not the same as turning them on the real amp.[10] That is the difference from an amp model built by a maker such as Zoom, whose DNA engine aims to behave like the amp when its virtual knobs move.

So change gain by picking a different model in the pack, and shape the tone with the plugin's EQ, a 6-band EQ with up to 15 dB of boost or cut per band,[4] or with the cabinet IR.

Do NAM A1 captures still work?

Yes, where the plugin or device supports A1. TONE3000 retrained its whole A1 library as A2, except models with no downloads that were more than 60 days old and models with malformed training data. Where it had the original recording, the new model was trained on it; where it did not, it trained the A2 model on synthetic data from the A1 model and labels it Convert.[2]

A2 is a new architecture, not a drop-in update, so a plugin or pedal that runs A1 cannot load A2 until its maker updates it.[2] NAM's official plugin, Gateway, plays both architectures.[12] You can still upload A1 models, but new captures on TONE3000 are trained as A2 only.

Which pedals and amps run NAM A2?

The list grows month by month. The table gives the units announced on TONE3000's own blog, with the date of each post. TONE3000 expects broad A2 support across the NAM ecosystem by the end of 2026.[2]

Some makers run NAM by converting it. TONE3000 names Hotone, Sonicake, Sonulab, Valeton and NUX among the companies that convert NAM A1 models into their own formats, and says those are not real NAM models.[2] Hotone has since announced A2-Lite for its Ampero II Stomp, Gearnews reported in October 2026.[10]

Hardware with native NAM A2, as announced on TONE3000's blog (checked 15 November 2026)
UnitA2 sizeWhat TONE3000 announced
Blackstar Beam MiniA2Native NAM A2 in an amp, a few weeks before the IGNIS (June 2026)
VTR Effects IGNISA2-LiteNative A2-Lite, a free upgrade for owners (4 June 2026)
Darkglass AnagramA2-Lite and A2-FullRuns both sizes, three A2-Full models at once (25 June 2026)
HeadRush Prime, Core, Flex PrimeA2Native NAM announced at A2's launch for that summer (2 June 2026)
Zoom NeurigA2NAM A2 and TONE3000 on the pedal; capturing your own gear from December 2026 (26 October 2026)
Fractal Audio Axe-Fx IIIA2With firmware 33 and Axe-Edit III 1.15.03 or later (30 October 2026)
Blackstar ID:X Floor One, Two, ThreeA2Free firmware update, up to 24 captures stored at once (12 November 2026)

NAM vs ToneX, Quad Cortex and Helix

The difference TONE3000 stresses is the file. A NAM capture works in any plugin, pedal or amp that supports NAM, the way an IR or a MIDI file does.[1] Captures made for Neural DSP's Quad Cortex, IK Multimedia's ToneX and Line 6's Helix work only in those makers' own products, and their systems are closed source.

TONE3000's library is free to browse and play, and capturing your own gear on it is free.[3] The commercial systems bring their own amp models and effects around the captures, which NAM on its own does not: the plugin's chain adds a gate, an EQ and IRs, and a NAM-capable pedal brings the rest.

Common questions

What is NAM A2?

NAM A2 is the second architecture of Neural Amp Modeler, the open-source amp capture software. TONE3000 launched it on 2 June 2026 with NAM's creator Steve Atkinson. One A2 model runs as A2-Full on computers or A2-Lite on pedals, and it replaced A1 as the default for new captures on TONE3000.

What is the difference between A2-Full and A2-Lite?

They are the same model at two sizes. A2-Full is the maximum-accuracy version for computers and devices with processing to spare, and TONE3000 says it uses 30 to 40% less CPU than A1-Standard. A2-Lite is the smaller size for pedals and small amps, and TONE3000 says it runs at 50% CPU on a $3 ARM Cortex-M7 chip.

What are the best Neural Amp Modeler input settings?

Turn the interface gain up while playing as hard as you ever will and stop below clipping, with the input switched to instrument. Then set the capture's Input on the block. For the response the capture's creator recorded, turn on Calibration and enter your interface's level, typically +12 dBu for pro gear or +4 dBu for semi-pro, per TONE3000.

Should I use calibration or normalization in NAM?

Leave Normalize on: it keeps every block at the same loudness when you swap captures. Calibration is optional and changes feel rather than volume, by hitting the capture at the input level its creator used. TONE3000 advises skipping it until you want to match a specific capture's feel.

Why does my NAM capture sound thin and harsh?

Usually because it is an Amp Head capture with no cabinet after it. TONE3000 says an Amp Head capture needs a speaker cabinet IR, or it sounds thin and harsh. Load a cabinet IR after it, or use an Amp + Cab capture, which already includes the cabinet.

Can I change the gain on a NAM capture?

Not the way you turn a real amp's knob. A capture is a snapshot of the gear at one setting, so turning the gain does not reproduce what the amp did. Packs often hold several models of the same amp at different knob settings: pick the one nearest the gain you want, and shape the rest with EQ and the cabinet IR.

Do my old NAM A1 captures still work?

Yes, in any plugin or device that supports A1. TONE3000 retrained almost its whole A1 library as A2, and NAM's official plugin, Gateway, plays both architectures. A plugin or pedal built for A1 cannot load A2 until its maker updates it, because A2 is a new architecture rather than a drop-in update.

Is Neural Amp Modeler free?

Yes. NAM is open source, A2 is MIT-licensed, and the TONE3000 plugin is free. TONE3000's library of captures is free to play, though loading a tone in the plugin needs a free account, and capturing your own gear on TONE3000 is free.

Which pedals support NAM A2?

By TONE3000's announcements up to 15 November 2026: the Blackstar Beam Mini and ID:X Floor range, the VTR Effects IGNIS, the Darkglass Anagram, HeadRush's Prime, Core and Flex Prime, the Zoom Neurig and Fractal Audio's Axe-Fx III with firmware 33. Some other makers convert NAM files into their own formats instead of running them natively.

Is NAM A2 better than ToneX or the Quad Cortex?

TONE3000's own tests say so: across 39 tones and a blind listening test with over 1,000 participants, it reports that A2 beat Neural DSP's Neural Capture V2, IK Multimedia's ToneX and Line 6's Proxy. These are the maker's tests. The practical difference is the file: NAM captures run in any NAM-capable product, ToneX and Quad Cortex captures only in their makers' own.

Sources

The numbers in brackets in the text point to this list.

Gear in this guide

Settings for your own amp

This guide covers what is true of every rig. For a specific song on a specific amp, Tonelify reads the documented chain behind the recording and returns gain, bass, middle, treble and presence values for the controls your amp actually has. A first plan starts with 7 days free, $0 today.

Keep reading