Blackstar ID:Core 20 V4 settings
There is no bass, middle or treble knob. The tone comes from the Voice setting and ISF, which sweeps between an American and a British voicing. The MOD, DLY and REV switches turn the modulation, delay and reverb on, and Effect Type and Effect Level set the one being edited.
⚡ Match a tone on this amp- Voice
- Gain
- Volume
- ISF
- MOD
- DLY
- REV
- Effect Type
- Effect Level
- Tap
How do you dial in a specific tone on a Blackstar ID:Core 20 V4?
The Blackstar ID:Core 20 V4 is a modelling amp, so a tone match here has two halves: which model or voicing to select, and where to set the controls once it is selected. Getting the second right on the wrong model gets you nowhere. Tonelify picks the voicing first and writes the knob positions against it, using the front panel this unit actually has.
Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact guitar amp, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.
Settings for this amp only ever use controls it actually has, because its front panel is stored in our gear database. You will not be told to set a knob that is not on the amp.

Free download
Printable cheat sheet: PDF and PNG
The clean, blues, classic rock, hard rock, lead and metal settings from this page, together on one sheet with short tips. The PDF prints on white; the PNG is the dark version for your phone.
Starting settings on the Blackstar ID:Core 20 V4
Positions on a 0 to 10 scale, with 5 at twelve o'clock. They are where to begin, not Blackstar's numbers: pick the voice first, then move one control at a time from here.
Clean
Clean Warm voice, Gain 3, ISF 5, REV on with the Plate reverb, Effect Level about 3. Blackstar calls Clean Warm a classic clean, and its product page adds dynamic: it follows how hard you pick. Keep Gain low and set the loudness with Volume. Volume is a preamp volume on this amp, and Blackstar says high settings bring in the effect of valve power amp distortion and compression, so a clean turned right up starts to thicken and squash. Clean Bright, which Blackstar describes as a boutique clean, is the other clean voice.
- Gain 3
- ISF 5
- Effect Level about 3
Edge of breakup and blues
Clean Bright voice, Gain 6 to 7, ISF 6, REV on with the Spring reverb, Effect Level about 3. Blackstar describes Clean Bright as a boutique clean that will break up when pushed hard: clean when you play softly, gritty when you dig in. Set Gain so the grit arrives with your picking hand, and roll the guitar's volume back to clean it up again. ISF a step past the middle, toward the British side, gives what Blackstar calls a more woody, less aggressive character.
- Gain 6 to 7
- ISF 6
- Effect Level about 3
Classic rock
Crunch voice, Gain 5, ISF 7, REV on with the Room reverb, Effect Level about 2. Blackstar calls Crunch a classic crunch sound with medium gain overdrive. With no bass, middle or treble knob, ISF is the tone control: clockwise, toward the British side, Blackstar describes the sound as more woody and less aggressive, and at 7 the crunch leans that way. Keep the reverb low so chords stay clear in a band. For solos, the Lead setting below uses OD 1, the voice Blackstar made for them.
- Gain 5
- ISF 7
- Effect Level about 2
Hard rock
Super Crunch voice, Gain 6, ISF 4, REV on with the Room reverb, Effect Level about 2. Blackstar describes Super Crunch as a modern driven gain with more punch than Crunch. ISF a step toward the American side gives the tight bottom end Blackstar describes for that end of the knob, so palm mutes stay defined. If the sound turns fizzy, lower Gain before anything else: there is no treble or presence knob to take it out.
- Gain 6
- ISF 4
- Effect Level about 2
Lead
OD 1 voice, Gain 6 to 7, ISF 6, DLY on with the Analogue delay, Effect Level about 3, and REV on with the Hall reverb. Blackstar's manual describes OD 1 as a hot-rodded master volume overdrive perfect for smooth solos. Press Tap in time with the song to set the delay time, or hold Tap and turn Effect Level to set it by hand. All three effect switches can be on at once, and Effect Level works on whichever one shows a green LED: press REV once to turn the reverb on and set its Effect Level to about 2, then press DLY to go back to the delay.
- Gain 6 to 7
- ISF 6
- Effect Level about 3
Metal
OD 2 voice, Gain 6 to 7, ISF 3, effects off. Blackstar describes OD 2 as a tight metal rhythm tone with mid boosted overdrive, and ISF toward the American side adds what Blackstar calls a tight bottom end and a more aggressive middle. Leave the effects off for rhythm parts, where reverb blurs palm mutes. If it fizzes, lower Gain a step before you move ISF: there is no treble or presence knob.
- Gain 6 to 7
- ISF 3
Saving the six as patches
The ID:Core stores six patches, one on each voice, so each setting above has a slot of its own, from the clean one on Clean Warm to the metal one on OD 2. Set the knobs and the effects, then hold Manual for two seconds: the Voice LED flashes to show the patch is stored, in place of whatever was there. Volume is not part of a patch, since Blackstar makes it a global setting, so set it last, for the room. With the Manual LED off, turning Voice recalls each patch; switch Manual on and the amp follows the knobs where they sit, with the effects turned off.
Chasing one song? Name it and the matcher writes that song's settings for the Blackstar ID:Core 20 V4.
Blackstar ID:Core 20 V4 voices
The Voice knob picks one of six voices, from clean to high gain, and each voice holds one patch. Each row gives Blackstar's own description from the V4 manual and the starting setting on this page that uses the voice.
| Voice | Setting here | What Blackstar says it is |
|---|---|---|
| Clean Warm | Clean | Classic clean |
| Clean Bright | Edge of breakup and blues | Boutique Clean, will break up when pushed hard |
| Crunch | Classic rock | Classic Crunch sound with medium gain overdrive |
| Super Crunch | Hard rock | A modern driven gain with more punch than Crunch |
| OD 1 | Lead | Hot-rodded Master Volume overdrive perfect for those smooth solos |
| OD 2 | Metal | A tight metal rhythm tone with Mid boosted overdrive |
Blackstar ID:Core 20 V4 effects list
Twelve effects, four on each of the MOD, DLY and REV switches, and one of each can run at the same time. Effect Type picks the effect from four segments and changes one setting by how far into the segment it is turned. Effect Level changes a second setting, and Tap sets the speed or time where the effect has one: tap it in time, or hold Tap and turn Effect Level.
| Effect | Switch | What the knobs set |
|---|---|---|
| Phaser | MOD | Effect Type sets the mix, Effect Level the depth and Tap the speed. |
| Chorus/Flanger | MOD | Effect Type sets the morph, Effect Level the mix and Tap the speed. |
| Envelope | MOD | Effect Type sets the sensitivity and Effect Level the depth. No Tap setting. |
| Tremolo | MOD | Effect Type sets the frequency modulation depth, Effect Level the amplitude modulation depth and Tap the speed. |
| Linear | DLY | Effect Type sets the feedback, Effect Level the delay level and Tap the time. |
| Analogue | DLY | Effect Type sets the feedback, Effect Level the delay level and Tap the time. |
| Tape | DLY | Effect Type sets the feedback, Effect Level the delay level and Tap the time. |
| Multi | DLY | Effect Type sets the feedback, Effect Level the delay level and Tap the time. |
| Room | REV | Effect Type sets the size and Effect Level the reverb level. No Tap setting. |
| Hall | REV | Effect Type sets the size and Effect Level the reverb level. No Tap setting. |
| Spring | REV | Effect Type sets the size and Effect Level the reverb level. No Tap setting. |
| Plate | REV | Effect Type sets the size and Effect Level the reverb level. No Tap setting. |
What controls does the Blackstar ID:Core 20 V4 have?
The Blackstar ID:Core 20 V4 has 10 controls on its front panel: Voice, Gain, Volume, ISF, MOD switch, DLY switch, REV switch, Effect Type, Effect Level and Tap.
Blackstar ID:Core 20 V4 specifications
- Power
- 20W, as 2x10W stereo
- Speaker
- 2x5" Blackstar
- Voicings
- Clean Warm, Clean Bright, Crunch, Super Crunch, OD 1, OD 2
- Front panel
- Voice, Gain, Volume, ISF, MOD switch, DLY switch, REV switch, Effect Type, Effect Level, Tap
- Released
- 2024
What the Blackstar ID:Core 20 V4 panel means when you dial it in
20W, as 2x10W stereo through a 2x5" Blackstar. At that rating it is built for practice and small rooms rather than for keeping up with a drummer. There is no bass, middle, treble or presence knob on this panel. The tone is set by the selected voice and the ISF control instead, so EQ numbers written for another amp have nothing to land on here. Drive and volume have separate knobs, so the amp can sound driven at a volume that is liveable. Where a tone sits between the two is part of the answer, not a detail. The selectable voicings are Clean Warm, Clean Bright, Crunch, Super Crunch, OD 1 and OD 2. Picking the voicing comes before the knob positions, because the same numbers land somewhere else on each one.
Blackstar ID:Core 20 V4 questions
Does the Blackstar ID:Core 20 V4 have bass, middle and treble knobs?
No. The tone comes from the Voice knob and ISF, which is printed EQ above the knob and ISF below it. Blackstar's manual says ISF fully counter clockwise has a more American characteristic, with a tight bottom end and a more aggressive middle, and fully clockwise a British one, more woody and less aggressive. ISF is saved with each patch.
What effects does the ID:Core 20 V4 have?
Twelve, four on each switch: Phaser, Chorus/Flanger, Envelope and Tremolo on MOD, Linear, Analogue, Tape and Multi on DLY, and Room, Hall, Spring and Plate on REV. Blackstar says the modulation, delay and reverb run simultaneously and are stored with the sound, and its product page describes the Envelope as an envelope filter for funky cleans or touch-sensitive lead lines.
How do you pick an effect, such as the Plate reverb, on the ID:Core?
Press the effect's switch until its LED is green: Blackstar calls that focused, and only the focused effect answers the Effect Type and Effect Level knobs. Effect Type is divided into four segments, one for each effect of that kind, with an LED showing which is active, and how far you turn into a segment changes one setting, such as the reverb's size. The panel numbers the segments 1 to 4 rather than naming them, so listen as you turn.
How do you save a patch on the ID:Core 20 V4?
Hold Manual for two seconds. The Voice LED flashes to show the patch is stored, and it replaces whatever was in that slot. There are six patches, one per voice, and each patch uses its own voice: the Clean Warm patch is on Clean Warm. Volume is not saved, because Blackstar makes it a global setting. To recall a patch, turn Voice with the Manual LED off.
Why does a knob do nothing when I turn it on the ID:Core?
That is the Recall Indicator at work. After a patch change the knobs may not match what you hear, so to prevent a jump in level, Gain, Volume and ISF do nothing until the knob reaches the value you are hearing. The Recall Indicator then flashes twice and the knob takes control. It flashes again each time the knob passes that value.
Does the ID:Core 20 V4 have a tuner?
Yes. Hold REV for one second. The output is muted while it is on, the Voice LEDs show the nearest string, and the effect LEDs show how close you are: MOD red means sharp, DLY green in tune and REV red flat. Press any button to leave the tuner.
Can you use a footswitch with the ID:Core 20 V4?
Yes, a Blackstar FS-11 or FS-18, which is not supplied. In its default mode switch 1 toggles between two patches you choose in Architect, Blackstar's software, and switch 2 turns all the patch's effects on and off. An alternative mode, also set in Architect, steps down and up through the patches, looping from OD 2 back to Clean Warm. The Stereo 10 V4 has no footswitch jack.
Does the ID:Core 20 V4 have Bluetooth?
No. Of the V4 range, only the ID:Core Stereo 10 V4 Bluetooth has it. On the 20, play along through the Line In / Streaming jack with a 3.5 mm cable and set the music's level on the player; holding Tap while you turn Volume turns the music down further on the amp.
Can you record or use headphones with the ID:Core 20 V4?
Yes. The CabRig & Phones jack carries the sound through CabRig Lite, Blackstar's speaker simulator, and mutes the speakers; Volume sets its level. Over USB-C the amp works as an audio interface with four channels out: the processed sound in stereo, the preamp before the effects with no speaker emulation, and the dry guitar for reamping. Windows needs Blackstar's USB audio driver; a Mac needs none.
What does the 1W button on the ID:Core 20 V4 do?
It is the Power Reduction button, printed 1W / 20W. Full power gives what Blackstar calls the loudest clean headroom, and 1W cuts the output stage to one watt for practice and recording at low volume, which Blackstar says it does without sacrificing tone.
What is the difference between the ID:Core V3 and V4?
The six voices, ISF and the 12 effects are the same, and so are the 20's power, weight and size. V4 adds power reduction to 1W, moves the USB socket to USB-C and adds a Stereo 10 V4 Bluetooth model, and Blackstar says the 40 V4 is louder than before.
Do these settings work on the ID:Core 10 V4 and 40 V4?
Yes, as a starting point. The 10 V4 and 40 V4 have the same voices, ISF and effects; they differ in power and speakers: 2x5W into two 3-inch speakers on the 10, 2x10W into two 5-inch on the 20 and 2x20W into two 6.5-inch on the 40. Only the 20 and the 40 take a footswitch.
What are the best Blackstar ID:Core 20 V4 settings for metal?
Start with OD 2, Gain 6 to 7, ISF 3 and the effects off. These are starting points rather than Blackstar's numbers. OD 2 is the voice Blackstar describes as a tight metal rhythm tone; for solos, OD 1 with a delay is the one to try. If it fizzes, lower Gain a step, since there is no treble or presence knob.
How do you factory reset the ID:Core 20 V4?
Hold MOD, DLY and REV while you switch the amp on. The Voice LEDs count down, and letting go before they go out cancels the reset. Then switch the amp off to complete it. A reset overwrites every patch you have stored.
Is there a printable ID:Core 20 V4 settings cheat sheet?
Yes. The cheat sheet on this page puts the six starting settings on one page, from clean to metal, each with its voice and effect, and short tips under them. Download the PDF to print it on white, or save the PNG to your phone.
Does Tonelify support the Blackstar ID:Core 20 V4?
Yes, and its front panel is stored, so settings only ever reference controls this guitar amp has: Voice, Gain, Volume, ISF, MOD switch, DLY switch, REV switch, Effect Type, Effect Level, Tap. You will not be told to set a knob that is not there.
Sources
Panel, specifications and dates checked against these on .
- Blackstar: ID:CORE V4 Owner's Manual (PDF)
- Blackstar: ID:CORE V4 product page
- Blackstar: ID:CORE V3 handbook (PDF), for what changed in V4
- Guitar World: NAMM 2024, Blackstar issues fourth generation of its best-selling ID:Core practice amp (23 January 2024)
Both manuals are the files Blackstar links from blackstaramps.com/product-handbooks; they are served from Blackstar's content delivery network.
More Blackstar gear
Similar amps from other makers
Settings for the song you are chasing
Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for the controls the Blackstar ID:Core 20 V4 has. A first plan starts with 7 days free, $0 today.