Tonelify
Black Friday40% off yearly
Multi-FX and modellersModelling pedal

Boss IR-2 presets and settings

Compact pedal with eleven amp types on Celestion cabinet IRs, two channels on the pedal switch, AMBIENCE, a stereo send/return after the amp, headphones, USB-C audio and IR loading, and a 9 V battery or PSA adaptor.

⚡ Match a tone on this unit

How do you dial in a specific tone on a Boss IR-2?

The Boss IR-2 plays Tone Models, and every Tone Model is a different amp or pedal, so a tone match here has two halves: which kind of Tone Model to load, and where to set the knobs once it is loaded. The Tone Model sets the character and Gain sets how hard it is driven, which is why the settings for the Boss IR-2 name the Tone Model first and write the knob values against it.

Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact multi-effects unit, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.

Boss IR-2 Settings Cheat Sheet: knob positions for clean, blues, classic rock, metal and lead on one page

Free download

Printable cheat sheet: PDF and PNG

The clean, blues, classic rock, metal and lead settings from this page, together on one sheet with short tips. The PDF prints on white; the PNG is the dark version for your phone.

Starting settings on the Boss IR-2

Positions as clock times, since the knobs carry no numbers: 12:00 is the middle of the travel. They are where to begin, not Boss's numbers: pick the amp model first, then move one control at a time from here.

Clean

CLEAN, BOSS's own amp with a natural clean sound in front of a 1x12" Celestion V-Type IR. Gain 10:00, Bass 12:00, Middle 12:00, Treble 1:00, Level 12:00, with AMBIENCE around 9:00 for a little room. BOSS prints no number scale for the IR-2's knobs, so these are clock positions. TWN, its model of a Fender Twin Reverb on a 2x12" Celestion A-Type, is the bigger, brighter clean. If the IR-2 feeds an amp rather than a desk or headphones, set its output first: the manual's OUTPUT SELECT procedure is in the list below.

CLEAN amp typeIR-2 clean
  • Gain 10:00
  • Bass 12:00
  • Middle 12:00
  • Treble 1:00
  • Level 12:00

AMBIENCE about 9:00 for a little room.

Edge of breakup and blues

TWEED, BOSS's model of a 1959 Fender Bassman 4x10" combo on a 4x10" Celestion G10 Gold IR. Gain 12:00, Bass 11:00, Middle 1:00, Treble 12:00, Level 12:00. Play softer and it cleans up; dig in and it breaks up. DIAMOND, BOSS's model of a VOX AC30 on two Celestion Blues, is the chimier choice. Your drive pedals go in front of the IR-2's INPUT, the way they would in front of an amp, so a low-gain overdrive here gives the push without more Gain.

TWEED amp typeIR-2 edge of breakup
  • Gain 12:00
  • Bass 11:00
  • Middle 1:00
  • Treble 12:00
  • Level 12:00

An overdrive pedal in front for more push.

Classic rock

BRIT, BOSS's model of a Marshall 1959 Super Lead on a 4x12" Celestion G12M-Heritage IR. Gain 1:00, Bass 12:00, Middle 1:00, Treble 1:00, Level 12:00. Keep MIDDLE past noon so the rhythm part holds its place in a band. CRUNCH is BOSS's own alternative, which it says uses MDP to deliver a crisp tone from all strings, on a 2x12" Celestion G12-65.

BRIT amp typeIR-2 classic rock
  • Gain 1:00
  • Bass 12:00
  • Middle 1:00
  • Treble 1:00
  • Level 12:00

CRUNCH for BOSS's own take.

Metal

RFIER, BOSS's model of the Channel 2 Modern mode of a MESA/Boogie Dual Rectifier on a 4x12" Celestion Vintage 30 IR. Gain 2:00, Bass 1:00, Middle 11:00, Treble 1:00, Level 12:00. MODDED is BOSS's own heavy amp, built to keep its definition even with extreme gain, and SLDN models a Soldano SLO-100. The manual lists no noise suppressor on the IR-2, so put a noise gate pedal before it if the hiss between riffs bothers you.

RFIER amp typeIR-2 metal
  • Gain 2:00
  • Bass 1:00
  • Middle 11:00
  • Treble 1:00
  • Level 12:00

A noise gate pedal before the IR-2 if it hisses.

Lead

BROWN, which BOSS calls a lead sound with a distinct edge and says is derived from the Katana series, on a 4x12" Celestion G12M-Heritage IR. Gain 2:00, Bass 12:00, Middle 2:00, Treble 12:00, Level 1:00. Put it on the red channel and your rhythm sound on the green one: the IR-2 holds two channels, each saving every knob, and the pedal switch flips between them. Level a little higher than the rhythm channel lifts the solo. Delay and reverb pedals go in the SEND and RETURN loop, after the amp.

BROWN amp typeIR-2 lead
  • Gain 2:00
  • Bass 12:00
  • Middle 2:00
  • Treble 12:00
  • Level 1:00

On the red channel, rhythm on the green.

Chasing one song? Name it and the matcher writes that song's settings for the Boss IR-2.

Match a song to this unit7 days free, $0 today

Boss IR-2 amp list

The type knob picks one of eleven amps, each paired with a Celestion IR that the IR-2 ships with. Five are BOSS's own designs; the others model the amps BOSS names. Load your own IR and it replaces the cabinet in that type's slot.

From BOSS's IR-2 Owner's Manual, pages 5 and 6, and the IR-2 product page. BOSS uses the brand names only to describe the sounds it emulates.
TypeWhat BOSS says it isCabinet IR (speaker, cabinet, mic)
CLEANBOSS original amp with a natural clean sound1x12" Celestion V-Type, closed, Royer R-121
TWNFender Twin Reverb2x12" Celestion A-Type, open, Sennheiser MD421 + Royer R-121
TWEED1959 Fender Bassman 4x10" combo4x10" Celestion G10 Gold, closed, Royer R-121 + Shure SM57
DIAMONDVOX AC302x12" Celestion Blue, open, Sennheiser MD421 + Royer R-121
CRUNCHBOSS original crunch that uses MDP for a crisp tone from all strings2x12" Celestion G12-65, open, Sennheiser MD421 + Royer R-121
BRITMarshall 1959 Super Lead4x12" Celestion G12M-Heritage, closed, Sennheiser MD421
HI-GAINBOSS original high gain that uses MDP for a wide range and separation4x12" Celestion G12M Creamback, closed, Sennheiser MD421
SLDNSoldano SLO-1004x12" Celestion Vintage 30, closed, Sennheiser MD421
BROWNBOSS original high-gain lead with a distinct edge, derived from the Katana series4x12" Celestion G12M-Heritage, closed, Sennheiser MD421
MODDEDBOSS original amp that uses MDP to keep its definition at extreme gain4x12" Celestion G12K-100, closed, Sennheiser MD421
RFIERMESA/Boogie Dual Rectifier, Channel 2 in Modern mode4x12" Celestion Vintage 30, closed, Sennheiser MD421

Boss IR-2 output settings

Tell the IR-2 what its outputs feed. Unplug the INPUT cable, set the type knob to TWEED, turn AMBIENCE, LEVEL and GAIN fully anticlockwise and BASS, MIDDLE and TREBLE fully clockwise, then hold the pedal switch while you plug the cable back in. The CHECK indicator blinks orange three times in a cycle. Pick the setting with the type knob and the AMBIENCE knob, as below, and press the pedal switch to save. OUTPUT A and B share one setting, and headphones always get LINE.

From BOSS's IR-2 Owner's Manual, pages 9 to 11.
SettingType knobAMBIENCE knob
LINE (factory setting): audio interface, keyboard amp, mixer, recorderCLEANFully anticlockwise
JC-120 RETURNTWNFully anticlockwise
JC-120 INPUTTWEEDFully anticlockwise
KATANA-100 RETURNDIAMONDFully anticlockwise
KATANA-100 INPUTCRUNCHFully anticlockwise
NEXTONE Artist RETURNBRITFully anticlockwise
NEXTONE Artist INPUTHI-GAINFully anticlockwise
TUBE COMBO 112 RETURNCLEANFully clockwise
TUBE COMBO 112 INPUTTWNFully clockwise
TUBE COMBO 212 RETURNTWEEDFully clockwise
TUBE COMBO 212 INPUTDIAMONDFully clockwise
TUBE STACK 412 RETURNCRUNCHFully clockwise
TUBE STACK 412 INPUTBRITFully clockwise

Boss IR-2 specifications

Released
2023

Boss IR-2 questions

What amps are in the Boss IR-2?

Eleven amp types, each paired with a Celestion IR: CLEAN, TWN (Fender Twin Reverb), TWEED (1959 Fender Bassman), DIAMOND (VOX AC30), CRUNCH, BRIT (Marshall 1959 Super Lead), HI-GAIN, SLDN (Soldano SLO-100), BROWN, MODDED and RFIER (MESA/Boogie Dual Rectifier, Channel 2 Modern). CLEAN, CRUNCH, HI-GAIN, BROWN and MODDED are BOSS's own designs, BROWN derived from the Katana series. The full table with each cabinet IR is below.

How do the two channels work on the IR-2?

Press the pedal switch to swap between the green and red channel; the CHECK indicator shows which one is on. Each channel saves every knob, type included, and saves by itself as you turn the knobs, but wait about two seconds after an edit before you switch channel or unplug, or the change is lost. Hold the pedal switch down to bypass. A footswitch in the CH SEL jack, an FS-5U, FS-6 or FS-7, can switch channels instead, and then the pedal switch only bypasses.

Why does the IR-2 sound different from where the knobs are?

Switching channel recalls that channel's saved sound, so the knobs may not show what you hear until you move them. Turning a knob applies it at once and saves it to the channel you are on.

How do you set the IR-2 for a guitar amp?

With OUTPUT SELECT. Unplug the INPUT cable, set the type knob to TWEED, turn AMBIENCE, LEVEL and GAIN fully anticlockwise and BASS, MIDDLE and TREBLE fully clockwise, then hold the pedal switch as you plug back in. Choose the setting with the type knob and the AMBIENCE knob, for a JC-120, a Katana-100, a NEXTONE Artist or a valve combo or stack, at its RETURN or its INPUT, and press the pedal switch to save. LINE, the factory setting, is for an audio interface, mixer or keyboard amp.

Can you load your own IRs into the Boss IR-2?

Yes, with BOSS's IR-2 IR Loader app for macOS or Windows over USB, after you install the IR-2 driver. It takes WAV files at 44.1, 48 or 96 kHz, 16 or 24-bit or 32-bit float, 200 or 500 ms long, and asks which channel to use from a stereo file. Each IR goes into a slot named after an amp type, and SLOT RESET puts a slot back to BOSS's Celestion IR.

Can you turn the amp or the cabinet off on the IR-2?

Yes. Unplug the INPUT cable, set the type knob to CLEAN, turn AMBIENCE, LEVEL and GAIN fully anticlockwise and BASS, MIDDLE and TREBLE fully clockwise, and hold the pedal switch as you plug back in. Then CLEAN keeps both on, TWN turns only the amp on, for an outside cabinet simulator, and TWEED only the cabinet, to use it as an IR loader. Press the pedal switch to save.

What does the AMBIENCE knob do on the IR-2?

It sets how much ambience goes on the sound. The type is ROOM from the factory, a warm small-room reverb; HALL and PLATE are the others. Change it the same way as the other hidden settings, with the type knob on TWN at power-up, then CLEAN for ROOM, TWN for HALL or TWEED for PLATE.

Can the IR-2 be used as an audio interface?

Yes, over its USB-C port, to record into a computer or an iOS device and to play backing tracks through it. Set the USB mode to match: VENDOR, the factory setting, with BOSS's driver for Windows and macOS, or GENERIC for an iOS device, which needs a Lightning to USB Camera Adapter. A charge-only USB cable will not work.

Can you use headphones with the Boss IR-2?

Yes, on its stereo mini PHONES jack, which always uses the LINE output setting whatever OUTPUT SELECT is set to. BOSS recommends the AC adaptor when you use the PHONES jack or USB, since both drain the battery faster.

How do you power the Boss IR-2?

With a 9 V alkaline battery, about 3.5 hours by BOSS's figure, or a BOSS PSA series AC adaptor. Plugging a cable into INPUT switches it on and unplugging switches it off, so unplug it when you finish to save the battery.

Does the Boss IR-2 work with bass?

Not really. BOSS says the IR-2 has no IR for bass amps or cabinets, so a bass sounds much the same through it.

How do the SEND and RETURN jacks work on the IR-2?

They are a loop after the amp, for modulation, delay and reverb pedals. RETURN is a TRS jack: set it to MONO, the factory setting, or STEREO for a stereo pedal, with the type knob on DIAMOND at power-up, then CLEAN for MONO or TWN for STEREO.

What are the best Boss IR-2 settings for metal?

Start with RFIER at Gain 2:00, Bass 1:00, Middle 11:00, Treble 1:00 and Level 12:00, or MODDED for BOSS's own extreme-gain amp. These are starting points rather than BOSS's numbers, since BOSS gives no knob values. A tight overdrive with low drive in front of the INPUT tightens palm mutes.

How do you factory reset the Boss IR-2?

Unplug the INPUT cable, set the type knob to BROWN and turn every other knob fully anticlockwise. Hold the pedal switch as you plug back in, then press it once when the CHECK indicator blinks orange. When it lights orange steadily, the reset is done.

How do you build a patch on the Boss IR-2?

Pick the amp model first, then set its controls, then add the blocks in signal-chain order: drive before the amp, time and modulation after it. A patch built the other way around ends up compensating for the wrong stage. Tonelify returns the model, the order and the parameters together.

Does Tonelify support the Boss IR-2?

Yes. Name it in the tone matcher along with the song you are chasing and the settings come back adapted to it. Gear does not need to be in the catalog for a match to run.

Sources

Panel, specifications and dates checked against these on .

The manuals are the English files BOSS's owner's manuals page links, read on 16 November 2026; the IR Loader manual is dated 2023. BOSS gives no knob values, so the five panels are starting points as clock positions.

More Boss gear

Similar multi-effects units from other makers

Settings for the song you are chasing

Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the Boss IR-2 in it. A first plan starts with 7 days free, $0 today.