Boss ME-80 presets and settings
Floor unit with a real knob per effect section, so a patch is dialled in by hand rather than through menus, plus eight footswitches and a treadle.
⚡ Match a tone on this unitHow do you dial in a specific tone on a Boss ME-80?
A multi-effects unit gives you the whole chain in one box, which means the order of the blocks is as much of the answer as the values inside them. Settings for the Boss ME-80 name the amp model, the block order and the parameters together, rather than handing you numbers with no chain to put them in.
Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact multi-effects unit, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.
Starting settings on the Boss ME-80
Positions as clock times, since the knobs carry no numbers: 12:00 is the middle of the travel. They are where to begin, not Boss's numbers: pick the amp model first, then move one control at a time from here.
Clean
CLEAN preamp type, which BOSS describes as a clean, uncoloured sound without a typical amp's trebly character or boomy low end. Gain 10:00 to 11:00, Bass 12:00, Middle 12:00, Treble 1:00, and the preamp's Level to set the patch's loudness. The REVERB knob picks the type and the amount in one: set it to a low HALL or SPRING value, holding EDIT as you turn it to see the number. For a wider clean, add CHORUS in EQ/FX2; for even picking, COMP in COMP/FX1 with SUSTAIN low.
- Gain 10:00 to 11:00
- Bass 12:00
- Middle 12:00
- Treble 1:00
Edge of breakup and blues
CRUNCH preamp type, BOSS's own crunch, which it says lets the nuances of your picking come through even more faithfully than on conventional combo amps. Gain 12:00, Bass 11:00, Middle 1:00, Treble 12:00. Dig in for grit and play lighter to clean up. For more push, switch on BLUES in OD/DS, BOSS's BD-2 sound, with DRIVE at 9:00 and LEVEL at 1:00, so it thickens the amp rather than taking it over. TWEED, the Fender Bassman's vintage crunch in BOSS's words, and COMBO, the VOX AC30's, are the vintage alternatives.
- Gain 12:00
- Bass 11:00
- Middle 1:00
- Treble 12:00
BLUES in OD/DS, DRIVE at 9:00 and LEVEL at 1:00, for more push.
Classic rock
STACK preamp type, which models input 1 of a Marshall 1959; BOSS calls it a vintage trebly sound suited to hard rock. Gain 1:00 to 2:00, Bass 12:00, Middle 1:00 to 2:00, Treble 11:00 to 12:00. Treble starts lower than on the other types because STACK is bright already. Keep the mids up: rock guitar sits in the midrange, and scooping it is the usual reason a patch sounds thin next to a band. For a solo, turn COMP/FX1 to SOLO, which BOSS says works with OD/DS and PREAMP to give a sound suited to solos.
- Gain 1:00 to 2:00
- Bass 12:00
- Middle 1:00 to 2:00
- Treble 11:00 to 12:00
Metal
METAL preamp type, BOSS's model of the heavily distorted sound of a Bogner Uberschall. Gain 12:00 to 1:00, Bass 1:00, Middle 11:00, Treble 1:00. For tighter palm mutes, switch on OD/DS with T-SCREAM, BOSS's model of the Ibanez TS-808, or BOOST, at DRIVE 9:00 and LEVEL 2:00, and take the preamp's Gain down a step. Set the noise suppressor by holding EDIT and pressing the BANK pedals, and raise it only until the hiss between chords goes: BOSS warns that too high a value can cut off notes you play softly. Presets 1-2 METAL AMP and 2-4 METAL RIFF are BOSS's own metal patches to compare against.
- Gain 12:00 to 1:00
- Bass 1:00
- Middle 11:00
- Treble 1:00
T-SCREAM or BOOST in OD/DS before you raise the Gain.
Lead
Start from the rhythm patch and set the CTL pedal to switch the solo in: in Memory mode, press the CTL button, press the pedals of the effects to switch together, such as OD/DS and DELAY, then save with WRITE. One press of CTL then turns them all on and the next turns them off. For the delay, turn its TYPE knob to TEMPO, set TIME to the dotted eighth or the quarter note, and press the DELAY pedal at least twice in time with the song; in Memory mode, press the number pedal of the current patch instead. Raise the preamp's Middle a little from the rhythm setting so the solo cuts through.
Acoustic guitar
Two routes, both in BOSS's manual. With an electro-acoustic guitar, use the AC preamp type, which BOSS says is suited to an electric acoustic guitar. With an electric guitar, turn COMP/FX1 to AC SIM, which changes the sound of an electric guitar into that of an acoustic, and shape it with LOW and HIGH; preset 8-4, E. gtr to A. gtr, is BOSS's own version of that patch. Keep OD/DS off and the reverb low.
Chasing one song? Name it and the matcher writes that song's settings for the Boss ME-80.
Boss ME-80 amp list
The PREAMP section has nine types, picked with its TYPE knob, and five knobs: Gain, Bass, Middle, Treble and Level. Each row gives BOSS's own description of the type; BOSS names a real amp behind five of them.
| Preamp type | What BOSS says it is |
|---|---|
| AC | Suited to an electric acoustic guitar |
| CLEAN | A clean, uncoloured sound without a typical amp's trebly character or boomy low end |
| TWEED | The vintage crunch sound of the Fender Bassman |
| CRUNCH | BOSS's own crunch, which lets the nuances of your picking come through even more faithfully than on conventional combo amps |
| COMBO | The vintage crunch sound of the VOX AC30 |
| LEAD | The sustaining vintage lead sound of the Boogie Mk series |
| DRIVE | BOSS's own straight drive sound for a broad range of styles, which BOSS says no existing amp gives |
| STACK | Input 1 of a Marshall 1959: a vintage trebly sound suited to hard rock |
| METAL | The heavily distorted sound of a Bogner Uberschall |
Boss ME-80 effects list
Eight sections, each with a knob that picks its type, and all eight can run at once; the REVERB knob picks the type and the amount together. The order is fixed: pedal effect, COMP/FX1, OD/DS, PREAMP, noise suppressor, foot volume, MOD, EQ/FX2, DELAY, REVERB. Where BOSS names the pedal or effect a type models, it is in brackets.
- COMP/FX1 (11)
- COMP, T. WAH UP, T. WAH DOWN, OCTAVE (one and two octaves down), SLOW GEAR, DEFRETTER (fretless guitar), RING MOD, AC SIM (electric to acoustic), Single to Hum, Hum to Single, SOLO
- OD/DS (11)
- BOOST, OVERDRIVE (BOSS OD-1), T-SCREAM (Ibanez TS-808), BLUES (BOSS BD-2), TURBO OD (BOSS OD-2, Turbo on), DISTORTION (BOSS DS-1), TURBO DS (BOSS DS-2, Turbo on), METAL DS (BOSS MT-2 Metal Zone), CORE (BOSS ML-2), FUZZ (Electro-Harmonix Big Muff), OCT FUZZ (Octavia)
- MOD (11)
- PHASER, FLANGER, TREMOLO, CHORUS, VIBRATO, PITCH SHIFT, HARMONIST, ROTARY, UNI-V (Uni-Vibe), DELAY (10 to 600 ms), OVERTONE
- EQ/FX2 (6)
- PHASER, TREMOLO, BOOST, DELAY (10 to 990 ms), CHORUS, EQ (3-band)
- DELAY (11)
- 1 to 99 ms, 100 to 600 ms, 500 to 6000 ms, ANALOG, TAPE, MODULATE, REVERSE, CHO + DELAY, TEMPO (tap tempo), TERA ECHO, PHRASE LOOP (38 seconds)
- REVERB (3)
- ROOM, HALL, SPRING
- PEDAL FX (10)
- WAH, VOICE, +1 OCT, +2 OCT, -1 OCT, FREEZE, OSC DELAY, OD/DS (drive), MOD RATE, DELAY LEV
Boss ME-80 preset list
The 36 presets sit in banks P1 to P9, four to a bank, and cannot be overwritten; save your own changes to one of the 36 user patches in banks U1 to U9. The last column is the pickup BOSS suits each preset to.
| Preset | Name | What BOSS says | Pickup |
|---|---|---|---|
| 1-1 | ROCK LEAD | Well sustained distortion sound, good for solos. | Either |
| 1-2 | METAL AMP | Powerfully distorted metal sound. The CTL pedal turns OCTAVE on, making the sound even heavier. | Humbucker |
| 1-3 | FUZZ ECHO | Fantasy-like sound using TERA ECHO, suitable for the progressive rock of the 70s. | Single coil |
| 1-4 | SPACE CLEAN | Clean sound with a broad spatial spread, suitable for arpeggios. | Either |
| 2-1 | OVERTONE DIST | Distortion sound rich in harmonic partials, using distortion and OVERTONE. The CTL pedal turns OVERTONE on and off. | Either |
| 2-2 | BLUES LEAD | Crunch sound suitable for blues. | Either |
| 2-3 | DS DRIVE | Rough distortion sound, good for backing. | Either |
| 2-4 | METAL RIFF | Metal sound good for riffs. The CTL pedal turns FLANGER on. | Humbucker |
| 3-1 | 60s FUZZ | Fuzz sound of the 60s with UNI-V. The expression pedal changes the UNI-V speed. | Either |
| 3-2 | 70s HARD ROCK | Drive sound for 70s hard rock. | Either |
| 3-3 | 80s METAL | Distortion sound for 80s metal. | Humbucker |
| 3-4 | 90s ALTERNATIVE | 90s alternative-rock sound. | Either |
| 4-1 | PHASE LEAD | Hard rock sound with PHASER. The CTL pedal turns FLANGER on. | Humbucker |
| 4-2 | VO CRUNCH | Crunch sound, good for chord strokes. | Either |
| 4-3 | METAL 4 Single | Metal sound, good for single-coil pickups. | Single coil |
| 4-4 | CLEAN RHYTHM | Tight, clean sound, good for rhythm. The CTL pedal turns PHASER on. | Humbucker |
| 5-1 | SURF TREMOLO | Tremolo sound, good for 60s surf rock. | Single coil |
| 5-2 | COUNTRY ECHO | Slap-back echo sound for country. | Single coil |
| 5-3 | T-WAH FUNK | Clean sound with T.WAH for funk. | Single coil |
| 5-4 | JAZZ 4 NECK PU | Jazz sound, suitable for the neck pickup. | Humbucker |
| 6-1 | WAH LEAD | Suited to solos that combine pedal wah and DISTORTION. | Either |
| 6-2 | FUSION LEAD | Mild lead sound for jazz fusion. | Either |
| 6-3 | PUNK DRIVE | Drive sound, good for punk rock. | Either |
| 6-4 | COMP CRUNCH | Crunch sound with COMPRESSOR for solos. | Single coil |
| 7-1 | CLEAN WAH | Clean sound with pedal wah, good for rhythm. | Either |
| 7-2 | PEDAL BEND | Raises the pitch by two octaves as you move the expression pedal. Suited to single-note phrases. | Either |
| 7-3 | ROTARY CRUNCH | Rotary sound of the 70s. The expression pedal changes the ROTARY speed. | Either |
| 7-4 | TALK PEDAL | An effect like a talk box as you move the expression pedal. | Either |
| 8-1 | LATIN LEAD | Sweet drive sound for Latin rock. The expression pedal controls the DELAY level. | Either |
| 8-2 | LIVERPOOL CLEAN | Clean tone for the 60s Liverpool sound. | Single coil |
| 8-3 | Single to Hum | Changes a single-coil pickup sound to a clean humbucker sound. | Single coil |
| 8-4 | E. gtr to A. gtr | Transforms the sound of an electric guitar into the sound of an acoustic guitar. | Single coil |
| 9-1 | Am/C TWIN LEAD | Twin-lead-like distortion sound for single-note phrases in A minor (C major). | Either |
| 9-2 | SYNTHY LEAD | Synth-like sound using SLOW GEAR. | Single coil |
| 9-3 | DEFRETTER | Fretless guitar sound. | Single coil |
| 9-4 | FREEZE | Sustains the notes when you advance the expression pedal. | Either |
Boss ME-80 specifications
- Released
- 2014
Boss ME-80 questions
What amps are in the Boss ME-80?
Nine preamp types on the PREAMP section's TYPE knob: AC, CLEAN, TWEED, CRUNCH, COMBO, LEAD, DRIVE, STACK and METAL. BOSS names the amp behind five: TWEED simulates the Fender Bassman's vintage crunch, COMBO the VOX AC30's, LEAD the vintage lead sound of the Boogie Mk series, STACK input 1 of a Marshall 1959 and METAL a Bogner Uberschall. CRUNCH and DRIVE are BOSS's own designs, AC is for an electro-acoustic guitar and CLEAN is uncoloured. BOSS's brochure says the preamps derive from its GT-100.
Which drive pedals does the ME-80 model?
OD/DS has eleven types, and BOSS names the pedal behind ten: OVERDRIVE is the BOSS OD-1, T-SCREAM the Ibanez TS-808, BLUES the BD-2, TURBO OD the OD-2 with Turbo on, DISTORTION the DS-1, TURBO DS the DS-2 with Turbo on, METAL DS the MT-2 Metal Zone, CORE the ML-2, FUZZ the Electro-Harmonix Big Muff and OCT FUZZ the Octavia. The eleventh, BOOST, is a gain booster that BOSS says also makes punchy clean tones on its own.
How do you save a patch on the ME-80?
Press WRITE, choose a user bank, U1 to U9, with the BANK pedals and a patch with number pedals 1 to 4, then press WRITE again. Everything except OUTPUT LEVEL is saved, and the unit switches to Memory mode. There are 36 user patches and 36 presets, which cannot be overwritten. An edit you do not save is lost when you change patch or switch off.
Why doesn't the ME-80 sound like its knobs show?
In Memory mode a patch loads its own values, so the knobs may not point where the patch is set. Hold EDIT and turn a knob to see its real value; the tuning guide lights when the knob's position matches it. A system setting decides what turning a knob does then: n0, the factory setting, changes the value at once, while n1 waits until the knob passes the stored value. Another, m0 or m1, decides whether switching to Manual mode takes the sound from the knobs or keeps the patch's.
Does the Boss ME-80 have a looper?
Yes. Turn the DELAY section's TYPE knob to PHRASE LOOP: press the DELAY pedal to record, again to play, and repeat to overdub, for up to 38 seconds in all. Press it twice within a second to stop. The loop is deleted when playback stops, when you move the TYPE knob or when you switch off, and BOSS says it cannot be saved.
How do you set the noise gate on the ME-80?
Its noise suppressor has no knob of its own: hold EDIT and press the BANK pedals to set the threshold to suit how much noise your pickups make. A value of 0 switches it off. BOSS warns that setting it higher than needed can cut off notes you play softly.
Can you use the ME-80 with headphones or straight into a mixer?
BOSS says the Gt. AMP OUTPUT jacks go to a guitar amp or a mixer, L alone for mono. Plugging a stereo mini plug into REC OUT/PHONES, for headphones or a recorder, switches on the internal guitar amp simulator, and the Gt. AMP OUTPUT jacks then carry the same sound. Over USB the ME-80 is an audio and MIDI interface once BOSS's driver is installed, and USB DRY REC lets you record the dry guitar while you hear the effects.
What power supply does the Boss ME-80 use?
A BOSS PSA-series AC adaptor, sold separately, or six AA batteries, which BOSS rates at about seven hours with alkalines and about two with carbon-zinc. It draws 200 mA. BOSS suggests keeping batteries in even on the adaptor, so the sound carries on if the cable is pulled out. Auto Off switches it off after 10 hours unused; the system settings turn that off.
What are the best Boss ME-80 settings for metal?
Start with the METAL preamp type at Gain 12:00 to 1:00, Bass 1:00, Middle 11:00 and Treble 1:00, with T-SCREAM or BOOST in OD/DS in front and the noise suppressor on. These are starting points rather than BOSS's numbers. If it fizzes, lower Gain first and Treble second.
When did the Boss ME-80 come out?
BOSS announced it in January 2014; Premier Guitar's report of the launch is dated 15 January 2014. BOSS's brochure describes it as a knob-based floor unit with eight footswitches, an expression pedal and a phrase looper, running on six AA batteries or a PSA-series adaptor.
How do you build a patch on the Boss ME-80?
Pick the amp model first, then set its controls, then add the blocks in signal-chain order: drive before the amp, time and modulation after it. A patch built the other way around ends up compensating for the wrong stage. Tonelify returns the model, the order and the parameters together.
Does Tonelify support the Boss ME-80?
Yes. Name it in the tone matcher along with the song you are chasing and the settings come back adapted to it. Gear does not need to be in the catalog for a match to run.
Sources
Panel, specifications and dates checked against these on .
More Boss gear
Similar multi-effects units from other makers
Settings for the song you are chasing
Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the Boss ME-80 in it. A first plan starts with 7 days free, $0 today.