Tonelify
Black Friday40% off yearly
PedalOctave

Boss OC-5 Octave settings

The -2 Oct/Range knob does one of two jobs. In Vintage mode it sets the level two octaves down; in Poly mode it becomes Range, which sets how much of the frequency range the octave effect covers.

⚡ Match a tone on this pedal
Front panel6 controls
  • Direct Level
  • +1 Oct Level
  • -1 Oct Level
  • -2 Oct/Range
  • Vintage/Poly
  • Guitar/Bass
The controls on the Boss OC-5 Octave, drawn in a row rather than in the real panel layout.

How do you dial in a specific tone on a Boss OC-5 Octave?

The Boss OC-5 Octave works on the note as the guitar plays it, so it usually goes at the front of the chain, before any drive. Fed an already distorted signal, a pitch effect can lose track of the note it is shifting. Settings here come with that position as well as the knob values.

Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact pedal, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.

Settings for this unit only ever use controls it actually has, because its front panel is stored in our gear database. You will not be told to set a knob that is not on the unit.

Starting settings on the Boss OC-5 Octave

Positions on a 0 to 10 scale, with 5 at twelve o'clock. They are where to begin, not Boss's numbers: move one control at a time from here.

Starting point: fatter riffs

Vintage mode, Direct Level 10, -1 Oct Level 4, -2 Oct/Range 2, +1 Oct Level 0. This is BOSS's own recipe from its article on octave pedals: set the clean blend fully clockwise, the -1 octave under halfway and the -2 at around nine o'clock, which is about 2 on a 0 to 10 reading. The clean signal still dominates, so the guitar stays clear while the octaves support and fatten each note. In Vintage mode the -2 Oct/Range knob is the level two octaves below; play single notes, as BOSS's manual says.

Boss OC-5OC-5 riff fattening
  • Direct Level 10
  • -1 Oct Level 4
  • -2 Oct/Range 2
  • +1 Oct Level 0

Vintage mode. Single notes, guitar first in the chain.

Synth bass

Vintage mode, Direct Level 0, -1 Oct Level 10, -2 Oct/Range 10, +1 Oct Level 0. BOSS's article says to roll off all the clean signal and blend the -1 and -2 octaves in to full clockwise rotation: without the strings' attack the sound is much less dynamic and more like a synthesizer, and with a high-gain amp it gives wild bass synth tones. Play one note at a time, low on the neck.

Boss OC-5OC-5 synth bass
  • Direct Level 0
  • -1 Oct Level 10
  • -2 Oct/Range 10
  • +1 Oct Level 0

Vintage mode. No dry guitar at all.

Organ chords

Poly mode, +1 Oct Level 7 to 8, -1 Oct Level 7 to 8, Direct Level 5 to 6, -2 Oct/Range 10. BOSS's article says to bring in the +1 and -1 octaves in equal measure at a relatively high setting, the clean signal slightly lower, and to play chords into a clean amp, ideally with some reverb, for organ-like sounds. The article also adds the -2 octave here, but BOSS's manual says that in Poly mode that knob works as Range, so turn it right to put the octave under the whole chord. The 7 to 8 and 5 to 6 readings are Tonelify's.

Boss OC-5OC-5 organ
  • +1 Oct Level 7 to 8
  • -1 Oct Level 7 to 8
  • Direct Level 5 to 6
  • -2 Oct/Range 10

Poly mode, clean amp, a little reverb.

Bass line under chords

Poly mode, -2 Oct/Range 0, -1 Oct Level 6 to 7, Direct Level 10, +1 Oct Level 0. BOSS's manual says that with the Range knob turned all the way to the left the effect applies only to the lowest note of the chord, and BOSS's product page calls that the Lowest setting. You get an octave bass line under normal chords. Range at 0 is BOSS's; the -1 Oct Level of 6 to 7 is Tonelify's starting point.

Boss OC-5OC-5 bass under chords
  • -2 Oct/Range 0
  • -1 Oct Level 6 to 7
  • Direct Level 10
  • +1 Oct Level 0

Poly mode. Range fully left is Lowest.

Twelve-string chime

Poly mode, +1 Oct Level 4 to 5, Direct Level 10, -1 Oct Level 0, -2 Oct/Range 0. BOSS's product page says the octave-up effect works in both Vintage and Poly modes, and that on its own it gives faux 12-string sounds and unique solo tones. Poly mode lets you strum chords. With the -1 octave off, Range does nothing here: BOSS's manual says it sets the bandwidth of the -1 octave effect. The values are Tonelify's.

Boss OC-5OC-5 octave up
  • +1 Oct Level 4 to 5
  • Direct Level 10
  • -1 Oct Level 0
  • -2 Oct/Range 0

Poly mode for chords. Add the +1 slowly.

Chasing one song? Name it and the matcher writes that song's settings for the Boss OC-5 Octave.

Match a song to this pedal7 days free, $0 today

What controls does the Boss OC-5 Octave have?

The Boss OC-5 Octave has 6 controls on its front panel: Direct Level, +1 Oct Level, -1 Oct Level, -2 Oct/Range, Vintage/Poly switch and Guitar/Bass switch.

Boss OC-5 Octave specifications

Front panel
Direct Level, +1 Oct Level, -1 Oct Level, -2 Oct/Range, Vintage/Poly switch, Guitar/Bass switch
Released
2021

What the Boss OC-5 Octave panel means when you dial it in

Its controls are Direct Level, +1 Oct Level, -1 Oct Level, -2 Oct/Range, Vintage/Poly switch and Guitar/Bass switch, and settings for this pedal are written against those names rather than a generic level, tone and gain.

Boss OC-5 Octave questions

What does the -2 Oct/Range knob do on the Boss OC-5?

It depends on the Vintage/Poly switch. BOSS's manual says that in Vintage mode it is the -2 Oct level, the volume of the sound two octaves below the direct sound. In Poly mode it is Range, which sets the bandwidth of the -1 octave effect: to the right the effect covers a wider range from low to high, to the left it is limited to the low notes, and fully left it applies only to the lowest note of a chord.

What is the difference between Vintage and Poly mode on the OC-5?

BOSS's manual says Vintage is a vintage sound that simulates the OC-2, for single notes, and Poly is a polyphonic mode that supports chords. BOSS's product page says Vintage reproduces the mono sound of the original OC-2 from 1982, and Poly is an evolved version of the Poly mode first introduced on the OC-3 Super Octave.

Can you play chords through the Boss OC-5?

Yes, in Poly mode. BOSS's manual says Poly is the polyphonic mode that supports chordal input, while Vintage mode is for single notes. Use the Range knob to choose which notes of the chord get the octave below.

Does the OC-5 have an octave up?

Yes. BOSS's product page says the +1 Oct knob adds an octave-up effect in both Vintage and Poly modes, on its own for faux 12-string sounds and solo tones, or blended with the octave-down effects for wider chord voicings and fat leads. With it, the OC-5 spans three octaves.

What does the Guitar/Bass switch on the OC-5 do?

BOSS's manual says it selects settings that suit a guitar or a bass, and BOSS's product page says it optimizes the tracking engine for the instrument you plug in. Set it to the instrument you are playing.

How does the Direct Out on the OC-5 work?

BOSS's manual says that with only the OUTPUT jack connected, the direct and octave sounds are mixed. With both OUTPUT and DIRECT OUT connected, the octave sound comes from OUTPUT and the direct sound from DIRECT OUT, and with the effect off the sound comes only from DIRECT OUT. BOSS's article suggests sending the octave down to a bass amp or DI to cover for a missing bass player.

Where should the OC-5 go in my pedal chain?

First, straight after the guitar. BOSS's manual says to connect it first in the chain, because if a guitar sound already processed by an effect goes into it, it might not work correctly. BOSS's article adds that a modulation effect in front of an octave pedal can make it glitch.

How long does a battery last in the Boss OC-5?

About 5 hours of continuous use on an alkaline battery, per BOSS's manual, with a current draw of 60 mA, so an adaptor from BOSS's PSA series, sold separately, is the better choice. The INPUT jack doubles as the power switch: the pedal is on whenever a cable is plugged into it.

Is the Boss OC-5 true bypass?

No. BOSS's specifications list buffered bypass. The input impedance is 1 M ohm and the output impedance 1 k ohm.

Does the OC-5 have latency?

BOSS's product page says its newly developed tracking technology gives more accurate response and natural feel with no latency, and that the OC-5 has wider range and more polyphonic capability than earlier OC models.

What is the OC-5 based on?

BOSS's OC-2 of 1982, which BOSS's product page calls the world's first modern octave pedal for guitar and bass. BOSS's article says the OC-3 replaced it in 2003 as the first polyphonic octave pedal, and that the OC-5 continued the line in 2021.

How big and heavy is the Boss OC-5?

73 mm wide, 129 mm deep and 59 mm high, and 440 g with its battery, per BOSS's manual.

Where does the Boss OC-5 Octave go in the signal chain?

Usually first, or close to it: straight after the guitar and before any drive pedal. It reads the note as the guitar plays it, and it does that most reliably on the plain guitar signal. The drive then shapes what this pedal has already done, rather than the other way round.

Does Tonelify support the Boss OC-5 Octave?

Yes, and its front panel is stored, so settings only ever reference controls this pedal has: Direct Level, +1 Oct Level, -1 Oct Level, -2 Oct/Range, Vintage/Poly switch, Guitar/Bass switch. You will not be told to set a knob that is not there.

Sources

Panel, specifications and dates checked against these on .

More Boss gear

Similar pedals from other makers

Settings for the song you are chasing

Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the Boss OC-5 Octave in it. A first plan starts with 7 days free, $0 today.