Tonelify
Black Friday40% off yearly
PedalDistortion

Boss MT-2 Metal Zone settings

⚡ Match a tone on this pedal
Front panel6 controls
  • Level
  • High
  • Low
  • Mid
  • Mid Freq
  • Distortion
The controls on the Boss MT-2 Metal Zone, drawn in a row rather than in the real panel layout.

How do you dial in a specific tone on a Boss MT-2 Metal Zone?

A drive pedal is not an amount of gain, it is a shape. The Boss MT-2 Metal Zone changes what reaches the amp's input, so where it sits in the chain and how the amp is set behind it matter as much as the pedal's own controls. Settings here cover both ends: the pedal, and the amp underneath it.

Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact pedal, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.

Settings for this unit only ever use controls it actually has, because its front panel is stored in our gear database. You will not be told to set a knob that is not on the unit.

Boss MT-2 Metal Zone Settings Cheat Sheet: knob positions for from noon, simon neil, amp boost, less fizz and lead on one page

Free download

Printable cheat sheet: PDF and PNG

The from noon, simon neil, amp boost, less fizz and lead settings from this page, together on one sheet with short tips. The PDF prints on white; the PNG is the dark version for your phone.

Starting settings on the Boss MT-2 Metal Zone

Positions as clock times, since the knobs carry no numbers: 12:00 is the middle of the travel. They are where to begin, not Boss's numbers: move one control at a time from here.

BOSS's starting point

Level 12:00, High 12:00, Low 12:00, Mid 12:00, Mid Freq 12:00, Distortion 12:00. BOSS's manual tells you to set the knobs as shown in the illustration, and the drawing has every knob at 12 o'clock. From there the manual goes through Distortion first, then Mid and Mid Freq, then High and Low, and Level last, set so there is no difference in volume between the effect and the straight sound. At 12:00 the EQ knobs are flat, since each one cuts to the left of center and boosts to the right.

BOSS's startMT-2 from noon
  • Level 12:00
  • High 12:00
  • Low 12:00
  • Mid 12:00
  • Mid Freq 12:00
  • Distortion 12:00

BOSS's manual drawing: every knob at 12 o'clock.

Simon Neil of Biffy Clyro

Level 3:00, Distortion just past 12:00, Low 3:00, High 12:00, Mid 10:00, Mid Freq 10:00. These are from BOSS's own article, in the words of Richard Pratt, Simon Neil's guitar tech: Level up to 3 o'clock, Distortion just over halfway, Low at 3 o'clock, High at 12 o'clock, and both midrange knobs back to around 10 o'clock. Pratt calls it a big, serious, scooped distortion, with the Low boost giving the sound girth. It runs into a 100 watt Marshall 1959 Super Lead reissue and a 4x12, so on a small amp it will sound fizzier.

From BOSS's articleMT-2 Simon Neil
  • Level 3:00
  • High 12:00
  • Low 3:00
  • Mid 10:00
  • Mid Freq 10:00
  • Distortion just past 12:00

His tech's setting, from BOSS's article. Into a 100 W Marshall and a 4x12.

Boost for a tube amp

Level cranked, Distortion low, High 12:00, Low 12:00, Mid 12:00, Mid Freq 12:00. In BOSS's article, Kurt Ballou of Converge says he used the MT-2 to push his old tube amps by cranking the output, keeping distortion low, and setting the EQ flat, and that even then it is far from transparent. Flat EQ on the MT-2 is every EQ knob at 12:00. Ballou gives no exact numbers for Level and Distortion, so set Level by ear until the amp breaks up the way you want.

From BOSS's articleMT-2 as a boost
  • Level cranked
  • High 12:00
  • Low 12:00
  • Mid 12:00
  • Mid Freq 12:00
  • Distortion low

Kurt Ballou's method from BOSS's article; he gives no numbers for Level and Distortion.

Less fizz

Level unity, Distortion 10:00, High 10:00, Low 12:00, Mid 1:00, Mid Freq 11:00. This one is Tonelify's, not BOSS's. It turns down Distortion and High, the two knobs that add the most fizz. BOSS's manual warns that if you set Distortion too high, the noise will increase and oscillation may occur. Lowering both and adding a little Mid around the lower middle of its range gives a thicker, smoother sound. Unity means as loud on as off.

Tonelify's startMT-2 with less fizz
  • Level unity
  • High 10:00
  • Low 12:00
  • Mid 1:00
  • Mid Freq 11:00
  • Distortion 10:00

Tonelify's starting point, not BOSS's.

Lead that cuts through

Level 1:00, Distortion 1:00, High 12:00, Low 11:00, Mid 2:00, Mid Freq 1:00. This one is Tonelify's, not BOSS's. A scooped setting sounds big alone and disappears in a band, so for solos boost Mid instead of cutting it, with Mid Freq a little past noon where the guitar's own voice sits. Level a little above the rhythm sound lifts the solo. BOSS's product page says the MT-2's Mid frequency can be set anywhere from 200 Hz to 5 kHz.

Tonelify's startMT-2 lead
  • Level 1:00
  • High 12:00
  • Low 11:00
  • Mid 2:00
  • Mid Freq 1:00
  • Distortion 1:00

Tonelify's starting point, not BOSS's.

Chasing one song? Name it and the matcher writes that song's settings for the Boss MT-2 Metal Zone.

Match a song to this pedal7 days free, $0 today

What each MT-2 knob does

The MT-2 has six knobs on four shafts: High and Low share one, Mid and Mid Freq share another. Every line here is from BOSS's manual.

From BOSS's MT-2 Owner's Manual, read on 7 November 2026.
KnobWhat it doesRange
DistortionSets the intensity of the distortionMin to max
HighBoosts or cuts the higher frequenciesPlus or minus 15 dB
LowBoosts or cuts the lower frequenciesPlus or minus 15 dB
MidBoosts or cuts the frequency set by Mid FreqCut to boost
Mid FreqSets the middle frequency200 Hz to 5 kHz
LevelSets the volume of the effectMin to max

What controls does the Boss MT-2 Metal Zone have?

The Boss MT-2 Metal Zone has 6 controls on its front panel: Level, High, Low, Mid, Mid Freq and Distortion.

Boss MT-2 Metal Zone specifications

Front panel
Level, High, Low, Mid, Mid Freq, Distortion
Released
1991

What the Boss MT-2 Metal Zone panel means when you dial it in

Its controls are Level, High, Low, Mid, Mid Freq and Distortion, and settings for this pedal are written against those names rather than a generic level, tone and gain.

Boss MT-2 Metal Zone questions

What is the best starting point for the Boss MT-2?

Every knob at 12 o'clock. That is how BOSS's manual draws the start, and at noon the High, Low and Mid knobs are flat. Then set Distortion, then the midrange, then High and Low, and set Level last so the pedal is as loud on as off.

How do the Mid and Mid Freq knobs work on the MT-2?

They are one stacked knob pair. BOSS's manual says the Mid Freq knob sets the frequency of the middle range, from 200 Hz to 5 kHz, and the Middle knob boosts or cuts that frequency. The manual also says that when the Middle knob is set to the center position, moving Mid Freq does not affect the sound, so turn Mid off center first and then sweep Mid Freq to hear it.

What are Simon Neil's MT-2 settings?

From BOSS's article, in his guitar tech Richard Pratt's words: Level up to 3 o'clock, Distortion just over halfway, Low at 3 o'clock, High at 12 o'clock and both midrange knobs at around 10 o'clock. Pratt says they only use the MT-2 with an amp with enough headroom, a 100 watt Marshall 1959 Super Lead reissue into a 4x12.

Why does my MT-2 sound fizzy?

Usually too much Distortion and High into an amp without headroom. Richard Pratt says in BOSS's article that with an amp without enough headroom, the midrange can sound a bit too fizzy. Lower Distortion and High, add some Mid, and set the amp clean. BOSS's manual also warns that a very high Distortion setting raises noise and can oscillate.

Does the MT-2 work into a clean amp?

Yes. BOSS's product page says the MT-2 works well with all types of guitar amplifiers, including clean pedal platform amps. Into a clean amp the pedal makes all of the distortion and the amp only sets the volume and the overall EQ.

What do the MT-2's EQ knobs do?

BOSS's manual says High and Low each boost when turned clockwise and cut when turned counterclockwise, with a range of plus or minus 15 dB. BOSS's product page calls the EQ a three-band active EQ with semi-parametric midrange, with up to 15 dB boost or cut on each band, placed after the distortion.

Is the MT-2 true bypass?

No. BOSS's product page lists buffered bypass.

What power does the MT-2 need?

A 9 V battery or a BOSS PSA series AC adaptor, per BOSS's manual, with a current draw of 30 mA. BOSS gives an expected battery life of about 12.5 hours for a carbon battery and 23.5 hours for an alkaline. The input jack doubles as the power switch, so unplug the input cable when you are not playing.

What is the difference between the MT-2 and the MT-2W?

BOSS's article says the MT-2W is the Waza Craft version, released in 2018, sold alongside the MT-2. It keeps the character of the original, with quieter operation and a lower noise floor in Standard mode, and a Custom mode for a wider range of tight, focused contemporary tones.

Who uses the Boss MT-2?

BOSS's article names Prince, Mark Linkous of Sparklehorse, Munky of Korn, Dave Mustaine of Megadeth, Kurt Ballou of Converge and Simon Neil of Biffy Clyro. BOSS's product page says the MT-2 came out in 1991, has sold over one million, and is BOSS's second most popular drive pedal ever, after the DS-1 Distortion.

What are the MT-2's specs?

Input impedance 1 M ohm, output impedance 1 k ohm, 73 x 129 x 59 mm and 385 g including the battery, per BOSS's manual and product page.

Where does the Boss MT-2 Metal Zone go in the signal chain?

In front of the amp input, before any time-based effects. Drive pedals interact with what the amp is already doing, so the amp's own gain setting is part of the answer and cannot be ignored when the pedal is dialled in.

Does Tonelify support the Boss MT-2 Metal Zone?

Yes, and its front panel is stored, so settings only ever reference controls this pedal has: Level, High, Low, Mid, Mid Freq, Distortion. You will not be told to set a knob that is not there.

Sources

Panel, specifications and dates checked against these on .

The noon start, the controls, power and specs are from BOSS's manual; bypass, history and amp advice are from BOSS's product page; the Simon Neil and Kurt Ballou settings are from BOSS's article. The less fizz and lead panels are Tonelify's, not BOSS's.

More Boss gear

Similar pedals from other makers

Settings for the song you are chasing

Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the Boss MT-2 Metal Zone in it. A first plan starts with 7 days free, $0 today.