Tonelify
Black Friday40% off yearly
PedalOverdrive

JHS Morning Glory V4 settings

The Gain switch engages a higher gain mode, and the Bright Cut switch on the side takes off the highest frequencies when the pedal sounds too bright.

⚡ Match a tone on this pedal
Front panel5 controls
  • Volume
  • Drive
  • Tone
  • Gain
  • Bright Cut
The controls on the JHS Morning Glory V4, drawn in a row rather than in the real panel layout.

How do you dial in a specific tone on a JHS Morning Glory V4?

A drive pedal is not an amount of gain, it is a shape. The JHS Morning Glory V4 changes what reaches the amp's input, so where it sits in the chain and how the amp is set behind it matter as much as the pedal's own controls. Settings here cover both ends: the pedal, and the amp underneath it.

Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact pedal, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.

Settings for this unit only ever use controls it actually has, because its front panel is stored in our gear database. You will not be told to set a knob that is not on the unit.

JHS Morning Glory V4 Settings Cheat Sheet: knob positions for clean boost, low-gain grit, crunch boost and gain lead on one page

Free download

Printable cheat sheet: PDF and PNG

The clean boost, low-gain grit, crunch boost and gain lead settings from this page, together on one sheet with short tips. The PDF prints on white; the PNG is the dark version for your phone.

Starting settings on the JHS Morning Glory V4

Positions as clock times, since the knobs carry no numbers: 12:00 is the middle of the travel. They are where to begin, not JHS's numbers: move one control at a time from here.

Clean boost

Volume 1:00, Drive 8:00, Tone 12:00, Gain switch down. This one is Tonelify's, not JHS's: JHS gives no knob positions. JHS's product page says the gain control sweeps from completely clean to rock'n'roll, and lists increased headroom and output for use as a full-frequency boost. With Drive low and Volume up, the pedal mostly makes the amp louder and pushes it a little harder.

Tonelify's startMorning Glory clean boost
  • Volume 1:00
  • Drive 8:00
  • Tone 12:00
  • Gain switch down

Tonelify's starting point, not JHS's.

Low-gain grit

Volume 12:00, Drive 11:00, Tone 11:00, Gain switch down. This one is Tonelify's, not JHS's. JHS's product page says to use the Morning Glory when you want to add some mid- to low-level grit to your crystal-clean tone. JHS's manual says that as you turn up the drive, it also adds brightness, so Tone sits a touch under noon here to keep the edge smooth.

Tonelify's startMorning Glory low-gain grit
  • Volume 12:00
  • Drive 11:00
  • Tone 11:00
  • Gain switch down

Tonelify's starting point, not JHS's.

Crunch boost

Volume 2:00, Drive 10:00, Tone 12:00, Gain switch down, into an amp that already crunches. This one is Tonelify's, not JHS's. JHS's product page says to use the Morning Glory when you want to boost a crunchy tone into thicker sustain. Keep Drive modest and let the extra Volume push the amp's own distortion.

Tonelify's startMorning Glory crunch boost
  • Volume 2:00
  • Drive 10:00
  • Tone 12:00
  • Gain switch down

Tonelify's starting point, not JHS's.

Gain toggle lead

Gain switch up, Drive 1:00, Volume 11:00, Tone 12:00, Bright Cut switch on. This one is Tonelify's, not JHS's. JHS's manual says the Gain toggle engages a higher gain mode when flipped up and the LED turns red; JHS's product page calls it a more powerful sound with enhanced low end and grit. Volume comes down because the mode is louder, and the Bright Cut switch on the right side cuts the highest frequencies if the lead turns harsh.

Tonelify's startMorning Glory Gain toggle lead
  • Gain switch up
  • Drive 1:00
  • Volume 11:00
  • Tone 12:00
  • Bright Cut switch on

Tonelify's starting point, not JHS's.

Chasing one song? Name it and the matcher writes that song's settings for the JHS Morning Glory V4.

Match a song to this pedal7 days free, $0 today

Morning Glory versions

JHS has made four versions of the Morning Glory. The years and the V1 to V3 changes follow JHS's story of the pedal; the V4 changes are from JHS's product page.

From JHS's story of the Morning Glory and its product page, read on 7 November 2026. The product page's shorter history puts the smaller box at V2 and the bright cut at V3.
VersionYearsWhat changed
V12007 to 2009Plain, bigger enclosure with stamped lettering
V22009 to 2010Toggle switch, high cut switch and JHS logo added
V32010 to 2015Smaller case, same circuit board
V4 (this page)2016 to nowTwo times more headroom, Gain toggle, Red Remote

What controls does the JHS Morning Glory V4 have?

The JHS Morning Glory V4 has 5 controls on its front panel: Volume, Drive, Tone, Gain switch and Bright Cut switch.

JHS Morning Glory V4 specifications

Front panel
Volume, Drive, Tone, Gain switch, Bright Cut switch
Released
2016

What the JHS Morning Glory V4 panel means when you dial it in

Its controls are Volume, Drive, Tone, Gain switch and Bright Cut switch, and settings for this pedal are written against those names rather than a generic level, tone and gain.

JHS Morning Glory V4 questions

What are good settings for the JHS Morning Glory?

JHS's manual gives no knob positions. Tonelify's starts: for a clean boost, Drive low around 8 o'clock and Volume around 1 o'clock; for low-gain grit, Drive and Tone near 11 o'clock with Volume at noon. JHS's manual says that as you turn up the drive it also adds brightness, so lower Tone as you raise Drive.

What does the Gain toggle on the Morning Glory V4 do?

JHS's manual says it engages a higher gain mode when flipped up, and the LED turns red to show it. JHS's product page calls it a more powerful sound with enhanced low end and grit, and says the LED changes from blue to red.

What does the Bright Cut switch do?

JHS's manual says the switch on the right side of the pedal cuts the highest frequencies in case the overall tone is too bright. JHS's product page says it tames high end on brighter rigs.

What is the Red Remote jack on the Morning Glory?

A jack for JHS's Red Remote footswitch, sold separately. JHS's manual says that with it you can toggle between the higher gain mode and the standard mode on the fly, so you get two voices from one pedal mid-song.

Is the Morning Glory a Bluesbreaker clone?

It started as one. JHS's story of the pedal says it began in late 2008 with a Bluesbreaker pedal built from a DIY kit, then modified to be louder and slightly different. Those prototypes became the Morning Glory.

When did the Morning Glory V4 come out?

In 2016. JHS's story of the pedal says the V4 debuted at Winter NAMM 2016 after about a two year design process, and that it is the version JHS is currently producing.

What changed on the Morning Glory V4?

JHS's product page lists two times more headroom, the Gain toggle and the Red Remote system. JHS's story says the V4 was revised from the V3 without changing it tonally, and the high cut moved to the side switch. The versions table below has the full history.

What power does the Morning Glory need?

9V DC, negative center. JHS's manual says do not use more than 9V DC or your warranty will be voided, and lists 43mA consumption.

Can the Morning Glory be used as a clean boost?

Yes. JHS's product page says the gain control sweeps from completely clean to rock'n'roll and lists increased headroom and output for use as a full-frequency boost. The Clean boost panel above has Tonelify's start.

Where does the Morning Glory go in the pedal chain?

Tonelify's advice, not JHS's: after tuner, compressor and wah, before modulation, delay and reverb. In front of another drive pedal it works as a boost; after one, it adds more gain and grit.

What does the Morning Glory V4 cost?

JHS's product page listed the Morning Glory V4 at $199.00 in the Internet Archive copy of 13 October 2026, which Tonelify read on 7 November 2026.

Where does the JHS Morning Glory V4 go in the signal chain?

In front of the amp input, before any time-based effects. Drive pedals interact with what the amp is already doing, so the amp's own gain setting is part of the answer and cannot be ignored when the pedal is dialled in.

Does Tonelify support the JHS Morning Glory V4?

Yes, and its front panel is stored, so settings only ever reference controls this pedal has: Volume, Drive, Tone, Gain switch, Bright Cut switch. You will not be told to set a knob that is not there.

Sources

Panel, specifications and dates checked against these on .

The controls, jacks and power are from JHS's manual; the description, V4 changes and price are from JHS's product page; the origin and version years are from JHS's story of the pedal. The manual and product page were read from Internet Archive copies because the live site refused automated requests. Every panel and the chain advice are Tonelify's, not JHS's.

Similar pedals from other makers

Settings for the song you are chasing

Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the JHS Morning Glory V4 in it. A first plan starts with 7 days free, $0 today.