M-VAVE Tank-G presets and settings
Battery multi-effects pedal with four footswitches and a knob for every block: noise gate, nine amps, three-band EQ, modulation, delay, reverb and eight IR slots. 36 presets in nine banks, about 12 hours per charge.
⚡ Match a tone on this unitHow do you dial in a specific tone on a M-VAVE Tank-G?
A multi-effects unit gives you the whole chain in one box, which means the order of the blocks is as much of the answer as the values inside them. Settings for the M-VAVE Tank-G name the amp model, the block order and the parameters together, rather than handing you numbers with no chain to put them in.
Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact multi-effects unit, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.
M-VAVE Tank-G presets (2026 preset pack)
36 presets in 9 banks of four, A to D. These are the presets M-VAVE lists for the New Year 2026 firmware, which replaces the presets, amps and IRs; back up your own tones first.
| Preset | Amp | Cab |
|---|---|---|
| 1A | J120_CL | None |
| 1B | VAVE_TS | AC-SeVin |
| 1C | VAVE_HTS | AC-SeVin |
| 1D | MS_GV2 | AC-SeVin |
| 2A | J900_CL | JVM_1960_57 |
| 2B | RAT_OD | JVM_1960_57 |
| 2C | VAVE_HTS | JVM_1960_57 |
| 2D | J900_HV | JVM_1960_57 |
| 3A | J120_CL | MESA_412 |
| 3B | RAT_OD | MESA_412 |
| 3C | VAVE_DS | MESA_412 |
| 3D | MS_HIGAIN | MESA_412 |
| 4A | J900_CL | WANGS112 |
| 4B | RAT_OD | WANGS112 |
| 4C | VAVE_DS | WANGS112 |
| 4D | MS_HIGAIN | WANGS112 |
| 5A | J120_CL | VOX_AC30 |
| 5B | VAVE_TS | VOX_AC30 |
| 5C | MS_GV2 | VOX_AC30 |
| 5D | J900_HV | VOX_AC30 |
| 6A | J900_CL | HIFI_YAMAHA |
| 6B | RAT_OD | HIFI_YAMAHA |
| 6C | VAVE_HTS | HIFI_YAMAHA |
| 6D | MS_HIGAIN | HIFI_YAMAHA |
| 7A | J120_CL | None |
| 7B | RAT_OD | EGNL_412 |
| 7C | VAVE_HTS | EGNL_412 |
| 7D | J900_HV | EGNL_412 |
| 8A | J120_CL | V30_MD421 |
| 8B | VAVE_TS | V30_MD421 |
| 8C | RAT_OD | V30_MD421 |
| 8D | J900_HV | V30_MD421 |
| 9A | VAVE_DS | AC-SeVin |
| 9B | MS_GV2 | MESA_412 |
| 9C | J900_HV | WANGS112 |
| 9D | MS_HIGAIN | HIFI_YAMAHA |
M-VAVE Tank-G amps (2026 firmware)
The nine TYPE positions after the New Year 2026 update. Six of the nine are based on drive pedals rather than amp heads, by M-VAVE's own descriptions.
| TYPE | Name | Type | M-VAVE says it is based on |
|---|---|---|---|
| 1 | J120_CL | Clean | Roland JC-120 Jazz Chorus |
| 2 | J900_CL | Clean | Marshall JCM900 |
| 3 | VAVE_TS | Overdrive | M-VAVE ODRIVE-TS |
| 4 | RAT_OD | Overdrive | Pro Co RAT |
| 5 | VAVE_HTS | Distortion | M-VAVE ODRIVE-TS, high gain |
| 6 | VAVE_DS | Distortion | M-VAVE MT1 |
| 7 | MS_GV2 | Distortion | Marshall GV-2 Guv'nor Plus |
| 8 | J900_HV | Distortion | Marshall JCM900 |
| 9 | MS_HIGAIN | Distortion | Marshall BB-2 Blues Breaker |
M-VAVE Tank-G cabs (2026 firmware)
Eight IR slots on the IR CAB knob; the first position turns the IR off. Each slot can be replaced with your own IR.
| Slot | Name | Cab | M-VAVE's sample |
|---|---|---|---|
| 1 | AC-SeVin | 2x10 | AC-SE210 with a U87 |
| 2 | JVM_1960_57 | 4x12 | JVM410 with an SM57 |
| 3 | MESA_412 | 4x12 | Mesa Boogie with an SM57 |
| 4 | WANGS112 | 1x12 | WANGS112 G12 with a U87 |
| 5 | VOX_AC30 | 2x12 | Vox AC30 with a U87 |
| 6 | HIFI_YAMAHA | 2x10 | Yamaha hi-fi with a U87 |
| 7 | EGNL_412 | 4x12 | ENGEL 412 (M-VAVE's spelling) with an MD421 |
| 8 | V30_MD421 | 1x12 | V30 with an MD421 |
M-VAVE Tank-G amps and cabs in the user manual
The amp and cab lists printed in M-VAVE's user manual, before the 2026 update replaced them. A unit that has not been updated may still have these.
| Slot | Amp | Amp type | Cab |
|---|---|---|---|
| 1 | Based on UWE-Twins 335 | Clean | VHT Deliverance 4x12 |
| 2 | Based on Archetype_C_W | Clean | Sperimental 4x12 |
| 3 | Based on TH-Mars VM410 | Overdrive | Electrovoice 2x10 |
| 4 | Based on Friedman 100 | Overdrive | Mesa Boogie 4x12 |
| 5 | Based on Brit Plex 50 | Overdrive | Fender Champ 1x8 |
| 6 | Based on Mars FD Hundred | Dist | Fender Pr Junior 1x10 |
| 7 | Based on Pea V 534 | Dist | Marshall 1960V30 4x12 |
| 8 | Based on Diesel_Hagan_6 | Dist | Diezel V30 4x12 |
| 9 | Based on EVH 5150 III 100S El34 | Dist | No ninth cab |
M-VAVE Tank-G footswitches and knobs
Two modes: PRESET mode loads presets, LIVE mode turns the knobs into a live amp and effects panel. B + C swaps between them.
| Control | What it does |
|---|---|
| A, B, C, D | PRESET mode: load preset A to D of the bank. LIVE mode: switch REVERB, DELAY, MOD and AMP on or off |
| A + B (BANK-) | Bank down; then tap A to D to load |
| C + D (BANK+) | Bank up; then tap A to D to load |
| Tap B + C | Swap between PRESET and LIVE mode |
| Hold B + C for 2 seconds | Tuner, with the output muted; tap B + C to leave |
| Hold B + C for 3 seconds | Bluetooth on or off |
| Hold A, B, C or D | Save the current sound to that slot of the chosen bank |
| NOISE GATE | Gate threshold; fully left turns it off |
| TYPE | Picks one of the nine amps |
| GAIN, TREBLE, MIDDLE, BASS, VOLUME | The amp's gain, three-band EQ and level |
| MOD FX and MOD SPEED | MOD FX picks chorus, phaser or tremolo by its third of the turn and sets its mix or depth; the gap between thirds turns MOD off |
| DLY MIX and DLY TIME | DLY MIX picks analog, tape or dual delay and sets the mix; DLY TIME sets the echo repeats |
| RVB DECAY and RVB MIX | RVB DECAY picks room, spring or cloud reverb and sets the decay; RVB MIX sets the level |
| IR CAB | Picks one of the eight IR slots, or off |
| MASTER | Final volume, except Bluetooth and USB playback |
M-VAVE Tank-G specifications
- Released
- 2023
M-VAVE Tank-G questions
What is the M-VAVE Tank-G?
A battery-powered multi-effects pedal for electric guitar. M-VAVE lists a noise gate, 9 amps, a 3-band EQ, 3 modulations, 3 delays, 3 reverbs, 8 IR cab slots and a tuner, with 36 editable presets. It has four footswitches and real knobs for each effect, a built-in battery that lasts 12 hours, an XLR output and USB-C audio. It measures 310 x 65 x 40 mm and weighs 613 g.
What effects does the M-VAVE Tank-G have?
One of each block in a fixed line: tuner, noise gate, amp with GAIN, TREBLE, MIDDLE, BASS and VOLUME, modulation (chorus, phaser or tremolo), delay (analog, tape or dual), reverb (room, spring or cloud) and an IR cab. Each of the three effect knobs picks its type by which third of the turn it sits in, and the gap between thirds turns that block off. There is no wah or compressor block.
What amps are in the M-VAVE Tank-G?
It depends on the firmware. The 2026 firmware, which M-VAVE says was developed using AM4, lists J120_CL (JC-120), J900_CL and J900_HV (JCM900), and six drive-based types: VAVE_TS, RAT_OD, VAVE_HTS, VAVE_DS, MS_GV2 and MS_HIGAIN. The user manual's older list runs from UWE-Twins 335 and Archetype_C_W cleans to Friedman 100, Brit Plex 50 and EVH 5150 III 100S El34 models. Both lists are on this page.
What are the presets on the M-VAVE Tank-G?
36 presets in 9 banks of four, A to D. In M-VAVE's 2026 preset pack, A presets are mostly clean or low gain on J120_CL or J900_CL, and B to D move through the drive types; by M-VAVE's descriptions J900_HV, VAVE_HTS and VAVE_DS are the heaviest, and MS_HIGAIN, despite its name, is a bluesy light distortion. Each bank from 1 to 8 keeps one cab, from AC-SeVin in bank 1 to V30_MD421 in bank 8; 1A and 7A run with no cab. The full table is on this page.
How do you change presets and banks on the M-VAVE Tank-G?
In PRESET mode, footswitches A to D load the four presets of the current bank. A and B together are BANK- and C and D together are BANK+: the bank number flashes, then tap A to D to load a preset from it. The screen shows the bank number from 1 to 9.
How do you edit and save a preset on the M-VAVE Tank-G?
Tap B + C for LIVE mode. The knobs then work live: a lit knob light means what you see is what you hear, a flashing one means the stored value differs until you turn that knob. The footswitches switch REVERB, DELAY, MOD and AMP on or off. To save, pick the bank with BANK- or BANK+ and hold A, B, C or D until it blinks quickly. The same hold in PRESET mode copies the current preset to another slot.
What are good settings for the M-VAVE Tank-G?
M-VAVE gives no knob settings; its starting points are the 36 presets, which you load and then adjust in LIVE mode. For a clean sound start from a J120_CL or J900_CL preset such as 1A or 2A; for crunch or blues, a VAVE_TS or MS_HIGAIN preset such as 1B or 3D; for high gain, J900_HV or VAVE_DS such as 2D or 3C. Turn NOISE GATE fully left if it cuts off quiet notes.
Can you load your own IRs into the M-VAVE Tank-G?
Yes, with the computer software or the app. Each import replaces one of the eight IR slots. M-VAVE's format is a 44.1kHz, 24-bit mono WAV of 1024 samples.
Can the M-VAVE Tank-G load NAM captures?
Yes, since firmware v98 of 27 October 2026. M-VAVE's notes say NAM and NAN models import through the companion software, and NAM models must be converted there first. The same update added stereo chorus, phaser, tremolo, delay and reverb. The January 2026 firmware added AM4 format files for the AMP module. Back up your tones before updating.
How long does the M-VAVE Tank-G battery last?
About 12 hours on a full charge, M-VAVE says. A 5V 2A adapter charges it in about 4 hours, and a power bank works too. The charging light is red while charging and blue when full, and the screen shows a low-battery sign every five seconds when it runs low. The battery is 3000mAh.
How do you use the tuner on the M-VAVE Tank-G?
Hold B and C for 2 seconds. The output mutes, the screen shows the note and the knob lights show the pitch: green in the middle when in tune, red to the left when flat and to the right when sharp. Sharps show as a dot after the note. The reference is fixed at 440 Hz. Tap B and C to leave.
Does the M-VAVE Tank-G have Bluetooth?
Yes. Hold B and C for 3 seconds to turn it on or off; the BT light flashes while it waits and stays lit when connected. Bluetooth plays music from your phone and connects the M-VAVE app for editing. The MASTER knob does not control Bluetooth or USB playback volume.
Can you record with the M-VAVE Tank-G?
Yes, three ways. Over USB-C it works as a computer sound card; a Loopback switch, on from the factory, mixes your computer or phone playback into the recording, and turning it off records only the guitar. It also records to a phone through the included recording cable, or through an OTG adapter on the USB port.
Does the M-VAVE Tank-G support MIDI?
Yes, since firmware v46 of 13 March 2024. M-VAVE's notes say PC00 to PC35 call the 36 presets and CC messages switch each module, such as reverb or delay, in either mode. The same notes add control from the Chocolate and Cube Turner pedals.
What are the outputs on the M-VAVE Tank-G?
A 1/4in mono output, an XLR balanced output for a mixer, PA or FRFR speaker, a 1/8in stereo headphone output and a phone recording jack. The input is a 1/4in mono jack. There is no effects loop and no expression pedal input.
How do you update the M-VAVE Tank-G firmware?
Download the firmware and update software from M-VAVE's downloads page; the latest Tank-G firmware listed there is V099 of 16 November 2026. M-VAVE warns that the 2026 update replaces the presets, amps and IRs, so back up your tones and settings first. The computer software can also restore factory settings.
How do you build a patch on the M-VAVE Tank-G?
Pick the amp model first, then set its controls, then add the blocks in signal-chain order: drive before the amp, time and modulation after it. A patch built the other way around ends up compensating for the wrong stage. Tonelify returns the model, the order and the parameters together.
Does Tonelify support the M-VAVE Tank-G?
Yes. Name it in the tone matcher along with the song you are chasing and the settings come back adapted to it. Gear does not need to be in the catalog for a match to run.
Sources
Panel, specifications and dates checked against these on .
- M-VAVE: TANK-G User Manual (PDF)
- M-VAVE: TANK-G NEW PRESET sheet (PDF)
- M-VAVE: downloads page, with Tank-G firmware V099 of 16 November 2026
- M-VAVE: Tank-G firmware release notes
- M-VAVE: TANK-G product page
The manual, preset sheet, downloads page and release notes were read on 17 November 2026. M-VAVE gives no knob values; the preset suggestions in the settings answer are Tonelify's picks from M-VAVE's preset table.
More M-VAVE gear
Similar multi-effects units from other makers
Settings for the song you are chasing
Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the M-VAVE Tank-G in it. A first plan starts with 7 days free, $0 today.