Tonelify
Black Friday40% off yearly
PedalReverb

TC Electronic Hall of Fame 2 settings

⚡ Match a tone on this pedal
Front panel5 controls
  • Decay
  • Tone
  • Level
  • Reverb Type
  • Pre-Delay
The controls on the TC Electronic Hall of Fame 2, drawn in a row rather than in the real panel layout.

How do you dial in a specific tone on a TC Electronic Hall of Fame 2?

Time and modulation effects sit at a specific point in a chain and change character completely if they move. Settings for the TC Electronic Hall of Fame 2 come with the position in the signal path, not just the knob values, because a delay in front of a driven amp and the same delay in a loop are two different sounds.

Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact pedal, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.

Settings for this unit only ever use controls it actually has, because its front panel is stored in our gear database. You will not be told to set a knob that is not on the unit.

Starting settings on the TC Electronic Hall of Fame 2

Positions as clock times, since the knobs carry no numbers: 12:00 is the middle of the travel. They are where to begin, not TC Electronic's numbers: move one control at a time from here.

Starting point: hall

Reverb Type Hall, Decay 11:00, Tone 12:00, Level 10:00, Pre-Delay switch short. TC's manual calls the Hall a broad yet slightly diffuse reverb, for large epic sounds at longer decay settings and ambient sounds at shorter ones. Level sets only how much reverb is mixed in: the manual says the dry signal always passes at its original, unity level. Decay sets the length of the reverb, and its maximum depends on the type, so recheck it when you change types.

HallHall of Fame 2 hall
  • Reverb Type Hall
  • Decay 11:00
  • Tone 12:00
  • Level 10:00
  • Pre-Delay switch short

Level adds reverb; the dry signal stays at unity.

Amp spring

Reverb Type Spring, Decay 12:00, Tone 1:00, Level 12:00, Pre-Delay switch short. TC's manual says the Spring reproduces the old spring reverbs of vintage guitar amps. Tone a little past noon brings out the drip: the manual says Tone sets the brightness of the reverb from dark to crisp. Pick near the bridge on a clean amp, and take Level up towards 2:00 for surf.

SpringHall of Fame 2 spring
  • Reverb Type Spring
  • Decay 12:00
  • Tone 1:00
  • Level 12:00
  • Pre-Delay switch short

Level towards 2:00 for surf.

Plate for leads

Reverb Type Plate, Decay 12:00, Tone 12:00, Level 10:00, Pre-Delay switch long. TC's manual says a plate is recognised by its very diffuse and bright sound and is excellent for guitar when you want a significant guitar reverb. The long Pre-Delay leaves a gap between the note and the reverb: the manual says a longer pre-delay helps keep presence and clarity with heavy reverb, so the solo stays in front.

PlateHall of Fame 2 plate
  • Reverb Type Plate
  • Decay 12:00
  • Tone 12:00
  • Level 10:00
  • Pre-Delay switch long

Long pre-delay keeps the lead clear.

Room for rhythm

Reverb Type Room, Decay 10:00, Tone 12:00, Level 11:00, Pre-Delay switch short. TC's manual says the Room simulates a relatively small, well-furnished room, where soft materials absorb many of the reflections. It adds space to strummed chords and riffs without a tail that runs into the next chord, so it can stay on all the time.

RoomHall of Fame 2 room
  • Reverb Type Room
  • Decay 10:00
  • Tone 12:00
  • Level 11:00
  • Pre-Delay switch short

Short tail, can stay on.

Shimmer ambient

Reverb Type Shim, Decay 3:00, Tone 11:00, Level 1:00, Pre-Delay switch long. TC's manual says the Shimmer pitch shifts the reverb up an octave through each feedback loop, for a haunting, other-worldly sound, and suggests pairing it with MASH. Play slow chords or single notes and let them ring. Tone a little below noon keeps the octave from getting piercing.

ShimHall of Fame 2 shimmer
  • Reverb Type Shim
  • Decay 3:00
  • Tone 11:00
  • Level 1:00
  • Pre-Delay switch long

Slow chords. Tone below noon if it gets piercing.

Chasing one song? Name it and the matcher writes that song's settings for the TC Electronic Hall of Fame 2.

Match a song to this pedal7 days free, $0 today

What controls does the TC Electronic Hall of Fame 2 have?

The TC Electronic Hall of Fame 2 has 5 controls on its front panel: Decay, Tone, Level, Reverb Type and Pre-Delay switch.

TC Electronic Hall of Fame 2 specifications

Front panel
Decay, Tone, Level, Reverb Type, Pre-Delay switch

What the TC Electronic Hall of Fame 2 panel means when you dial it in

Its controls are Decay, Tone, Level, Reverb Type and Pre-Delay switch, and settings for this pedal are written against those names rather than a generic level, tone and gain.

TC Electronic Hall of Fame 2 questions

What reverb types does the Hall of Fame 2 have?

Eight, plus three TonePrint slots. TC's manual lists Room, Hall, Spring, Plate, Church, Shim (Shimmer), Mod (Modulated) and LoFi (Low-Fidelity) on the Reverb Type selector, and three TonePrint settings for TonePrints you load or make yourself.

How does the MASH footswitch work?

Tap it to turn the reverb on or off. TC's manual says that if you press slightly harder and hold it down, MASH engages and the MASH LED lights; as you press harder the LED gets brighter and the assigned parameter rises. Release it and MASH stops, but the pedal stays on. Full MASH needs only 10 kg, around 20 pounds, of pressure.

Can I choose what MASH controls?

Yes. TC's manual says that with the TonePrint Editor software you can assign your own parameter to MASH and save it as a custom preset, and that the editor can also rewire what each knob controls.

Why is there no sound on TonePrint 3?

That is the default setting. TC's quick start guide says the default TonePrint 3 setting mutes the output, and that you use the MASH switch like a volume pedal to bring the volume up gradually.

What does the Level knob on the Hall of Fame 2 do?

It sets how much reverb is mixed in, nothing else. TC's manual says the direct, unprocessed signal is always passed through at its original, unity level, and Level only controls how much reverb is mixed with it.

What does the Pre-Delay switch do?

TC's manual says pre-delay is the time between the direct sound and the reverb, and that a longer pre-delay can help keep presence and clarity when you use heavy reverb.

What is the difference between the Hall and Church reverbs?

TC's manual calls the Hall a broad yet slightly diffuse reverb for large or ambient sounds, and the Church a highly diffuse, large reverb that emulates the hard surfaces of a church. It says to try Church if you want a large reverb and find the Hall too clean and subtle.

What do the Mod and LoFi reverbs sound like?

TC's manual says the Mod reverb puts modulation effects on the reverb tail, is really noticeable and cuts through live. It calls LoFi a down and dirty reverb, the opposite of the smooth studio types.

Where should the Hall of Fame 2 go in my signal chain?

In front of the amp, TC's manual says it is generally best after your other pedals. It also works in the amp's effects loop: the manual says it has a very wide gain range for guitar or loop-level signals, so connect the amp's Send to its input and its output to the amp's Return.

Is the Hall of Fame 2 stereo?

Yes. It has two inputs and two outputs. TC's manual says that with stereo effects in front, you can keep the stereo signal by using both inputs and sending the two outputs to different amps or a stereo mixer input.

Is the Hall of Fame 2 true bypass?

By default, yes, with buffered bypass as an option. TC's manual suggests buffered bypass on the first and last pedals of a chain if you use a long cable from the guitar, many pedals, or a long cable to the amp. The upper of two DIP switches under the back plate, the one nearer the power jack, sets the mode.

What is Kill-dry on the Hall of Fame 2?

It removes the direct signal from the output, for a parallel effects loop. TC's manual says the lower DIP switch under the back plate turns it on, and that it only works in Buffered Bypass mode.

How do I load a TonePrint into the Hall of Fame 2?

With the free TonePrint app. TC's manual says to plug your guitar into the pedal and turn the pedal on, turn up the guitar's volume with the selector on one pickup, then hold the phone's speaker next to that pickup and touch Beam to pedal.

What power supply does the Hall of Fame 2 need?

9 V DC, centre negative, on a standard 5.5/2.1 mm plug, not included. TC's quick start guide asks for more than 100 mA and the specifications in its manual more than 300 mA, so a supply rated for 300 mA or more covers both. The manual suggests isolated outputs to keep hum down. It also runs on a 9 V battery.

What is new on the Hall of Fame 2 over the original?

TC's manual says the Hall of Fame 2 adds MASH, which works like an expression pedal built into the footswitch, and a new Shimmer effect, to the original Hall of Fame. TC's product page also lists TonePrint support with three dedicated slots, true bypass with an optional buffered mode, and Analog-Dry-Through.

Where does the TC Electronic Hall of Fame 2 go in the signal chain?

After the drive stage. Running a time or modulation effect into a distorted input smears the repeats into the distortion instead of layering them over it, which is why this kind of pedal usually belongs in an effects loop where the amp has one.

Does Tonelify support the TC Electronic Hall of Fame 2?

Yes, and its front panel is stored, so settings only ever reference controls this pedal has: Decay, Tone, Level, Reverb Type, Pre-Delay switch. You will not be told to set a knob that is not there.

Sources

Panel, specifications and dates checked against these on .

More TC Electronic gear

Similar pedals from other makers

Settings for the song you are chasing

Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the TC Electronic Hall of Fame 2 in it. A first plan starts with 7 days free, $0 today.