TC Electronic Flashback 2 settings
⚡ Match a tone on this pedal- Delay
- Feedback
- Level
- Delay Type
- Subdivision
How do you dial in a specific tone on a TC Electronic Flashback 2?
Time and modulation effects sit at a specific point in a chain and change character completely if they move. Settings for the TC Electronic Flashback 2 come with the position in the signal path, not just the knob values, because a delay in front of a driven amp and the same delay in a loop are two different sounds.
Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact pedal, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.
Settings for this unit only ever use controls it actually has, because its front panel is stored in our gear database. You will not be told to set a knob that is not on the unit.

Free download
Printable cheat sheet: PDF and PNG
The slapback, dotted eighth, tape lead and crystals settings from this page, together on one sheet with short tips. The PDF prints on white; the PNG is the dark version for your phone.
Starting settings on the TC Electronic Flashback 2
Positions as clock times, since the knobs carry no numbers: 12:00 is the middle of the travel. They are where to begin, not TC Electronic's numbers: move one control at a time from here.
Slapback
Delay Type Analog, Delay 8:00, Feedback 8:00, Level 12:00, Subdivision switch quarter note. This one is Tonelify's, not TC Electronic's: TC gives no knob positions. TC's quick start guide says Feedback determines the number of delay repeats, so keep it low for one quick echo right behind each note, the rockabilly and country sound. Turn Delay down until the echo almost sticks to the note.
- Delay Type Analog
- Delay 8:00
- Feedback 8:00
- Level 12:00
- Subdivision switch quarter note
Tonelify's starting point, not TC Electronic's.
Dotted eighth rhythm
Delay Type 2290, Subdivision switch dotted eighth, Delay 12:00, Feedback 10:00, Level 11:00. This one is Tonelify's, not TC Electronic's. TC's guide says the Subdivision switch selects between quarter note, dotted eighth note, or quarter plus dotted eighth note repetitions. On dotted eighth, steady eighth notes and the repeats fill in each other's gaps for the rolling sound used in a lot of modern rock and worship parts. Set the time to the song with Delay or tap tempo.
- Delay Type 2290
- Subdivision switch dotted eighth
- Delay 12:00
- Feedback 10:00
- Level 11:00
Tonelify's starting point, not TC Electronic's.
Tape lead
Delay Type Tape, Delay 11:00, Feedback 11:00, Level 11:00, Subdivision switch quarter note. This one is Tonelify's, not TC Electronic's. TC's product page lists hyper-realistic tape warble and self-oscillation among its delays, so the repeats here wobble and darken a little like an old echo unit. Keep Level under the dry note for leads; turning Feedback far up is how the delay starts to run away on its own.
- Delay Type Tape
- Delay 11:00
- Feedback 11:00
- Level 11:00
- Subdivision switch quarter note
Tonelify's starting point, not TC Electronic's.
Crystals ambient
Delay Type Crystals, Delay 2:00, Feedback 1:00, Level 10:00, Subdivision switch quarter plus dotted eighth. This one is Tonelify's, not TC Electronic's. TC's product page says Crystals pitch shifts the echoes up an octave through each delay loop, which gives a shimmering trail behind slow chords. Long time and higher Feedback let the octaves stack up; play sparse notes and let them ring.
- Delay Type Crystals
- Delay 2:00
- Feedback 1:00
- Level 10:00
- Subdivision switch quarter plus dotted eighth
Tonelify's starting point, not TC Electronic's.
Chasing one song? Name it and the matcher writes that song's settings for the TC Electronic Flashback 2.
Flashback 2 controls
What each control and jack does, in TC Electronic's words from the quick start guide.
| Control | What TC's guide says |
|---|---|
| Delay | Adjusts the delay time |
| Feedback | Determines the number of delay repeats |
| Level | Adjusts the level of the delay repeats |
| Delay Type | Selects the delay type or TonePrint 1 to 3 |
| Subdivision | Quarter note, dotted eighth, or quarter plus dotted eighth repeats |
| Footswitch | Tap for on or off; push down and hold for MASH |
| USB | Firmware updates and TonePrint editing |
| Power | 9 V, over 100 mA, supply not included |
What controls does the TC Electronic Flashback 2 have?
The TC Electronic Flashback 2 has 5 controls on its front panel: Delay, Feedback, Level, Delay Type and Subdivision switch.
TC Electronic Flashback 2 specifications
- Front panel
- Delay, Feedback, Level, Delay Type, Subdivision switch
What the TC Electronic Flashback 2 panel means when you dial it in
Its controls are Delay, Feedback, Level, Delay Type and Subdivision switch, and settings for this pedal are written against those names rather than a generic level, tone and gain.
TC Electronic Flashback 2 questions
What is MASH on the Flashback 2?
A pressure sensor in the footswitch. TC's quick start guide says to tap the footswitch to turn the effect on or off, and to push down and hold to engage MASH and control the selected parameter. TC's product page says the harder you press, the more the assigned parameter increases, and full MASH needs only 10 kg of pressure. The TonePrint editor lets you assign your own parameter to it.
How do I use the Flashback 2 looper?
Set the delay type selector to LOOP, then record and overdub as many times as you like. TC's product page says a loop runs up to 40 seconds in mono or 20 seconds in stereo.
Why is there no sound on TonePrint 3?
Because the default TonePrint 3 setting mutes the output. TC's quick start guide says to use the MASH switch like a volume pedal to increase volume gradually. Press the footswitch down to bring the sound in, or load another TonePrint into that slot.
What delay types does the Flashback 2 have?
TC's product page lists 2290, Analog, Tape, Dynamic, Modulated, Crystals and Reverse. Dynamic lowers the delay level while you play and raises it between phrases; Crystals pitch shifts the echoes up an octave through each delay loop. The same selector also picks LOOP and TonePrint slots 1 to 3.
How long can the Flashback 2 delay be?
TC's product page says most types reach from 20 ms to 7,000 ms. The Subdivision switch then sets whether the repeats fall on quarter notes, dotted eighths or both.
Does the Flashback 2 have tap tempo?
Yes, two ways. TC's product page says the stereo input doubles as a tap tempo input for an external pedal. TC's firmware 1.2.00 release notes add a tap mode with no external switch: turn MASH off in the TonePrint app, then press and hold the footswitch; the bypass LED turns green and the tempo averages over two taps.
What power does the Flashback 2 need?
A 9 V power supply rated over 100 mA, which TC's quick start guide says is not included. TC's product page says it can also run on a battery.
Is the Flashback 2 true bypass?
Yes. TC's product page lists true bypass for zero high-end loss when the pedal is off, and Analog-Dry-Through, which keeps the dry signal analog even when the delay is on.
What is TonePrint on the Flashback 2?
Custom delay settings you load into the pedal. TC's product page lists 3 dedicated TonePrint slots, the free TonePrint App for loading signature tones and the free TonePrint Editor for building your own delays from scratch.
How do I update the Flashback 2 firmware?
Connect it to a computer by USB, which TC's quick start guide says is for firmware updates and TonePrint editing. TC's firmware 1.2.00 release notes say to connect the power cable while holding down the footswitch; the bypass LED turns green for boot mode, ready for the update.
Where does the Flashback 2 go in the pedal chain?
Tonelify's advice, not TC Electronic's: after drive and modulation pedals, near the end of the chain, so the repeats stay clean and separate. Into a dirty amp, try the amp's effects loop if it has one.
Where does the TC Electronic Flashback 2 go in the signal chain?
After the drive stage. Running a time or modulation effect into a distorted input smears the repeats into the distortion instead of layering them over it, which is why this kind of pedal usually belongs in an effects loop where the amp has one.
Does Tonelify support the TC Electronic Flashback 2?
Yes, and its front panel is stored, so settings only ever reference controls this pedal has: Delay, Feedback, Level, Delay Type, Subdivision switch. You will not be told to set a knob that is not there.
Sources
Panel, specifications and dates checked against these on .
- TC Electronic: Flashback 2 Delay quick start guide (PDF)
- TC Electronic: Flashback 2 Delay product page
- TC Electronic: Flashback 2 firmware 1.2.00 release notes (PDF)
The controls, power and the TonePrint 3 note are from TC's quick start guide; the delay types, MASH, looper, TonePrint and bypass details are from TC's product page; the tap tempo mode and boot mode are from TC's firmware 1.2.00 release notes. Every panel and the chain advice are Tonelify's, not TC Electronic's.
More TC Electronic gear
Similar pedals from other makers
Settings for the song you are chasing
Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the TC Electronic Flashback 2 in it. A first plan starts with 7 days free, $0 today.