NUX MG-400 presets and settings
Floor unit with four footswitches, a built-in expression pedal and a 2.8 inch colour screen. 26 amps and 36 cabinet IRs in the manual, ten movable blocks, three scenes a preset, a 60 second looper and USB recording; the GEN2 firmware adds a 10-slot NAM Loader.
⚡ Match a tone on this unitHow do you dial in a specific tone on a NUX MG-400?
A multi-effects unit gives you the whole chain in one box, which means the order of the blocks is as much of the answer as the values inside them. Settings for the NUX MG-400 name the amp model, the block order and the parameters together, rather than handing you numbers with no chain to put them in.
Name the song you are chasing in the tone matcher and Tonelify returns the settings for this exact multi-effects unit, not the settings the original artist used. Those are two different things: the recording was made on gear most players do not own.

Free download
Printable cheat sheet: PDF and PNG
The clean, blues, classic rock, metal and lead settings from this page, together on one sheet with short tips. The PDF prints on white; the PNG is the dark version for your phone.
Starting settings on the NUX MG-400
Positions as clock times, since the knobs carry no numbers: 12:00 is the middle of the travel. They are where to begin, not NUX's numbers: pick the amp model first, then move one control at a time from here.
Clean
TWIN RVB. Gain 9:00, Bass 12:00, Mid 12:00, Treble 1:00, with LEVEL to balance it against your other presets; this amp has BRIGHT where most have PRES. NUX's manual draws the knobs without numbers and lists no preset values, so every setting on this page is a starting point given as a clock position. Press EDIT/EXIT to open the AMP block, turn KNOB 1, 2 and 3 for the first page and press CTRL/PAGE for BASS, MID and TREB. For width, put CE-1 in the MOD block, whose knobs are INTEN., DEPTH and RATE, and pick TWIN 212 in the IR block.
- Gain 9:00
- Bass 12:00
- Mid 12:00
- Treble 1:00
CE-1 in MOD for width, TWIN 212 in IR.
Edge of breakup and blues
BRIT BLUES. Gain 12:00, Pres 12:00, Bass 11:00, Mid 1:00, Treble 12:00. Dig in for grit and play lighter to clean up. For more push, put T SCREAMER in the EFX block: its knobs are DRIVE, TONE and LEVEL, so keep DRIVE low and LEVEL up to push the amp rather than replace its grit. BLUES DRIVE and MORNING DRIVE sit in the same block. BRIT 212 in the IR block suits it.
- Gain 12:00
- Pres 12:00
- Bass 11:00
- Mid 1:00
- Treble 12:00
T SCREAMER in EFX, DRIVE low, LEVEL up.
Classic rock
PLEXI 100. Gain 2:00, Pres 12:00, Bass 12:00, Mid 1:00, Treble 1:00. Keep the mids up: rock guitar sits in the midrange, and scooping it is the usual reason a preset sounds thin next to a band. PLEXI 45, BRIT 800 and 1987 x 50W follow it in the manual's amp pages; GREEN 412 or G12M 412 in the IR block are the 4x12s to try first.
- Gain 2:00
- Pres 12:00
- Bass 12:00
- Mid 1:00
- Treble 1:00
Metal
UBER HIGAIN, last in the manual's electric amps. Gain 2:00, Pres 12:00, Bass 1:00, Mid 11:00, Treble 1:00, with UBER 412 in the IR block. Turn on the NR block, whose knobs are THRE. and DECAY, just high enough to quiet the hiss between chords. For tighter palm mutes, put T SCREAMER in EFX with DRIVE low, and take the amp's Gain down a step. DUAL RECT with RECT 412 and DIE VH4 are the next amps to try.
- Gain 2:00
- Pres 12:00
- Bass 1:00
- Mid 11:00
- Treble 1:00
NR on; T SCREAMER in EFX before you raise Gain.
Lead
SLO 100. Gain 2:00, Pres 12:00, Bass 12:00, Mid 1:00, Treble 12:00, with DIGI DELAY in the DLY block at a low LEVEL; its other knobs are F.BCK and D.TIM. Tap the TAP button in PRESET mode to set the tempo for the delay. To switch between a rhythm and a lead sound in one preset, assign a CTRL footswitch to SCN: each preset has three scenes, and the manual says the delay and reverb trails carry on when a scene turns them off.
- Gain 2:00
- Pres 12:00
- Bass 12:00
- Mid 1:00
- Treble 12:00
DIGI DELAY in DLY, LEVEL low; TAP for tempo.
Chasing one song? Name it and the matcher writes that song's settings for the NUX MG-400.
NUX MG-400 amp list
The manual's Reference pages show 24 electric guitar amps, one bass amp and one acoustic amp, each with the three knobs on its first page; BASS, MID and TREB sit on the second page, which CTRL/PAGE turns to. NUX does not say which amps they are modelled on, so they are given by name only. NUX's product page adds that firmware V2.1.1 brought 2 more amps and that the GEN2 firmware adds 3 Deep Image amps and 10 NAM Loader slots, without naming them, so the list here is the manual's.
| Amp | Kind | First-page knobs |
|---|---|---|
| JAZZ CLEAN | Electric | GAIN, BRIGHT, LEVEL |
| DELUXE RVB | Electric | GAIN, LEVEL |
| BASSMATE | Electric | GAIN, PRES, LEVEL |
| TWEEDY | Electric | GAIN, TONE, LEVEL |
| TWIN RVB | Electric | GAIN, BRIGHT, LEVEL |
| HIWIRE | Electric | GAIN, PRES, LEVEL |
| CALI CRUNCH | Electric | GAIN, PRES, LEVEL |
| CLASS A15 | Electric | GAIN, CUT, LEVEL |
| CLASS A30 | Electric | GAIN, CUT, LEVEL |
| PLEXI 100 | Electric | GAIN, PRES, LEVEL |
| PLEXI 45 | Electric | GAIN, PRES, LEVEL |
| BRIT 800 | Electric | GAIN, PRES, LEVEL |
| 1987 x 50W | Electric | GAIN, PRES, LEVEL |
| SLO 100 | Electric | GAIN, PRES, LEVEL |
| FIREMAN HBE | Electric | GAIN, PRES, LEVEL |
| DUAL RECT | Electric | GAIN, PRES, LEVEL |
| DIE VH4 | Electric | GAIN, PRES, LEVEL |
| VIBRO KING | Electric | GAIN, BRIGHT, LEVEL |
| BUDDA | Electric | GAIN, CUT, LEVEL |
| MR.Z.38 | Electric | GAIN, CUT, LEVEL |
| SUPER RVB | Electric | GAIN, BRIGHT, LEVEL |
| BRIT BLUES | Electric | GAIN, PRES, LEVEL |
| MATCH D30 | Electric | GAIN, CUT, LEVEL |
| UBER HIGAIN | Electric | GAIN, PRES, LEVEL |
| MLD | Bass | GAIN, MASTER, BASS |
| STAGEMAN | Acoustic | GAIN, MASTER, BASS |
NUX MG-400 cab list
The IR block holds 25 guitar cabinets, 8 bass cabinets and 3 acoustic guitar IRs, the same counts NUX's product page gives. NUX says the guitar cabinets combine 4 classic microphones with 3 mic positions; the manual's screens show the U87 at CENTER. Each preset also has a USER slot for an IR of your own, and there are 12 IR COLLECTION slots, loaded through QuickTone.
- IR EG CAB (25)
- JAZZ 212, BLACK 112, TWEED 410, TWEED 112, TWIN 212, CUSTOM 412, CALI 112, BLUE 112, BLUE 212, GREEN 412, G12L 412, T75 412, V30 412, SLO 412, HBE 412, RECT 412, BOTM 412, VIBRO 212, EVL 112, BUTQ 212, SUPER 212, BRIT 212, DC 212, G12M 412, UBER 412
- IR BASS CAB (8)
- AGL DB810, AMP SV212, AMP SV410, AMP SV810, BASSGUY 410, EDEN 410, MKB 410, TRC 410
- ACOUSTIC IR (3)
- G-HBIRO, G-J15, M-D45
- Microphones, from Bonedo's review (4)
- C414, E906, U87, SM-57
NUX MG-400 effects list
The manual's Reference screens, block by block, with the knobs each model shows on its first page. The expression pedal can also run a wah: NUX's GEN2 firmware page says holding PEDAL switches the pedal to WAH mode with 4 wah types, and adds 5 Deep Image effects to the EFX block without naming them here.
- NR (1)
- NR (THRE., DECAY)
- CMP (3)
- RED COMP (OUT., SENS.), ROSE COMP (SUST., LEVEL), STUDIO COMP (THRE., RATIO, GAIN)
- EFX (15)
- DIST+ (OUT., SENS.), RC BST (GAIN, VOL., BASS), AC BST (GAIN, VOL., BASS), DIST UNO (LEVEL, TONE, DRIVE), T SCREAMER (DRIVE, TONE, LEVEL), BLUES DRIVE (LEVEL, TONE, GAIN), MORNING DRIVE (VOL., DRIVE, TONE), MODERN DIST (DIST., FILT., VOL.), RED DIST (DRIVE, TONE, LEVEL), CRUNCH (VOL., TONE, GAIN), MUF DIST (VOL., TONE, SUST.), KATANA (BOOST, VOL.), ST SINGER (VOL., GAIN, FILT.), RED FUZZ (GAIN, TONE, OUT.), TOUCH WAH (MODE, DECAY, SENS.)
- EQ (2)
- 6-EQ, 10 BAND
- MOD (14)
- CE-1 (INTEN., DEPTH, RATE), CLASSIC CHORUS (RATE, DEPTH), ST.CHORUS (INTEN., WIDTH, RATE), VIBRATO (RATE, DEPTH), DETUNE (SHI.L, MIX, SHI.R), FLANGE (LEVEL, RATE, WIDTH), PH 90 (SPEED), PHASE 100 (INTEN., SPEED), CHORUS+ (SPEED, WIDTH, CH/FL), U-VIBE (SPEED, VOL., INTEN.), TREM (RATE, DEPTH), RTY SPK (BALAN, SPEED), HARMONY (KEY, MOD, HARM), SCH-1 (RATE, DEPTH, TONE)
- DLY (7)
- ANALOG DELAY (RATE, ECHO, INTEN), DIGI DELAY (LEVEL, F.BCK, D.TIM), MODULATE (TIME, LEVEL, MOD), TAPE ECHO (TIME, LEVEL, REPE.), REVERSE (TIME, MIX, F.BCK), PAN (TIME, REPE., LEVEL), PHI DELAY (MIX, REPE., TIME)
- RVB (6)
- ROOM (DECAY, TONE, LEVEL), HALL (DECAY, PRE.D, LIVE.), PLATE (DECAY, LEVEL), SPRING (DECAY, LEVEL), SHIMMER (MIX, DECAY, SHIM), DAMP (MIX, DEPTH)
NUX MG-400 specifications
- Released
- 2022
NUX MG-400 questions
What is the NUX MG-400?
A floor amp modeller and multi-effects unit from NUX, announced in September 2022: Premier Guitar gave its street price as $219 and gearnews its list price as 239 euros. It has two DSP chips, a 2.8 inch colour screen, four footswitches (UP, DOWN, CTRL1 and CTRL2) and a built-in expression pedal. NUX's manual gives its size as 289 by 163 by 71 mm and its weight as 920 g, and it runs on a 9V supply, which comes in the box.
What amps are in the NUX MG-400?
The manual shows 24 electric guitar amps, from JAZZ CLEAN, DELUXE RVB and TWIN RVB to PLEXI 100, BRIT 800, SLO 100, DUAL RECT and UBER HIGAIN, plus the MLD bass amp and the STAGEMAN acoustic amp. NUX does not say which amps they are modelled on. Its product page adds that firmware V2.1.1 brought 2 more amps and that the GEN2 firmware adds 3 Deep Image amps, without naming them. The full list is below.
Can the NUX MG-400 load NAM files?
Yes, with the GEN2 firmware. NUX's product page says GEN2 adds a NAM Loader with 10 slots for Neural Amp Modeler files: A2-Lite .nam files load natively and A1 files are converted. NUX lists GEN2 firmware V3.0.3, dated 28 August 2026, and warns that it works only with the GEN2 QuickTone editor, V2.6.8.24. The same update adds 3 Deep Image amps, which NUX calls its own amp modelling, 5 Deep Image effects and 4 wah types.
How many effects does the MG-400 have?
The manual's Reference pages show 48 models outside the amps and cabinets: the NR noise gate, 3 compressors, 15 EFX drives and boosts (with TOUCH WAH), 2 EQs, 14 modulation effects, 7 delays and 6 reverbs. The GEN2 firmware adds 5 Deep Image effects and 4 wah types for the expression pedal. A preset runs ten blocks, NR, CMP, EFX, AMP, IR, EQ, MOD, DLY, RVB and P.L, and you can move them in any order.
How do you change the block order on the MG-400?
Press EDIT/EXIT, then use LEFT and RIGHT to move the green target to a block. A short press on SELECT turns that block on or off. A long press turns the target red, and LEFT and RIGHT then move the block along the chain; a short press on SELECT turns it green again. NUX's product page adds that since firmware V2.1.1 you can hold a block to swap it for a second of another kind, such as two delays or two drives.
Can you load IRs into the MG-400?
Yes, through NUX's QuickTone editor. NUX gives the IR resolution as 512 samples, with files up to 48 kHz. Each preset has a USER slot for its own IR, and there are 12 IR COLLECTION slots besides. The built-in IRs are 25 guitar cabinets, 8 bass cabinets and 3 acoustic guitar IRs, and NUX says the guitar cabinets combine 4 microphones with 3 mic positions.
How do scenes work on the MG-400?
Each preset has three scenes, S1, S2 and S3, which turn its blocks on and off. Press CTRL/PAGE in PRESET mode to open CTRL SETTING and assign CTRL1 or CTRL2 to SCN; that footswitch then steps through S1, S2 and S3. Choose SCN3: OFF to toggle S1 and S2 only. The manual says the delay and reverb trails carry on when a scene turns them off. Press SAVE to keep the assignment with the preset.
How do you use the tuner on the MG-400?
Press CTRL1 and CTRL2 together. A short press on SELECT switches between Chromatic and Cmp G, which NUX calls its guitar compensation tuning; turning SELECT switches between mute and monitoring, and KNOB 2 sets A4 from 430 to 450 Hz. Press both footswitches again, or EDIT/EXIT, to leave the tuner.
How long is the MG-400 looper?
60 seconds in mono or 30 seconds in stereo. Press JAM, then use CTRL1 (LOOP): one press records, the next plays and the next overdubs; holding it undoes and redoes the last overdub; two presses stop the loop, and press and hold clears it. NR mode starts recording when you press the switch, and AR mode waits until you hit the strings. NUX says the looper fits the phrase to the drum tempo.
Does the MG-400 have a drum machine?
Yes. Press JAM, and CTRL2 (DRUM) starts and stops it. The manual's screen shows ten styles: ROCK, CTRY, BLUES, METAL, FUNK, JAZZ, BALD, POP, REGGA and ELEC. Tapping the TAP button in JAM sets the drum speed, and the second page holds the drum EQ. NUX's GEN2 notes add that holding TAP opens direct BPM input from 40 to 240.
What can the MG-400's expression pedal control?
Press PEDAL to choose the block it runs: WAH, EFX, AMP, MOD, DLY or RVB. With GEN2, holding PEDAL switches the pedal straight to WAH mode, with 4 wah types. In the SYSTEM MENU, EXP Independent makes the pedal act like a separate one that stays on when you change preset, and EXP CALIBRATION sets its range; NUX says to calibrate again after a firmware update.
How do you use the MG-400 with a guitar amp?
Press MODE and turn SELECT to one of five output modes: STUDIO DIRECT, COMBO FRONT, COMBO REAR, STACK FRONT and STACK REAR. KNOB 1 to 3 set a global LOW, MID and HIGH EQ for the mode. NUX says every mode except STUDIO DIRECT turns the IR block off by default, so a real amp's speaker does the cabinet's job. Press EDIT/EXIT to leave the output modes.
Can the MG-400 record to a computer?
Yes. Over the USB port it works as an audio interface at 48 kHz and 32 bit. In the SYSTEM MENU, USB SETTINGS has three routings, NORMAL, DRY OUT and REAMP, with KNOB 1 for the record level and KNOB 2 for the playback level. NUX's product page adds a Loopback option in Normal mode for live streaming, and NUX publishes ASIO drivers for Windows.
How do you update the MG-400's firmware?
NUX's update guide: download the update kit from the product page and install the NUX Device Updater. Hold the DOWN and CTRL1 footswitches while you turn the power on to enter DFU mode, connect the USB-C cable, choose the .bin file and click Start Update. It takes about 8 to 10 minutes, and you must not unplug anything meanwhile. The manual then asks for a FACTORY RESET and an EXP CALIBRATION.
What is the difference between the MG-400 and the MG-300?
NUX built the MG-400 on the MG-300 with the same amp modelling, and added movable signal blocks, 12 IR COLLECTION slots, a P.L block with MIN and MAX settings, a larger SYSTEM MENU and a physical MASTER knob, on two DSP chips. It also has four footswitches against the MG-300's two, three scenes in each preset and a 2.8 inch colour screen. Our NUX MG-300 page has that unit's settings and lists.
How much power does the MG-400 need?
9V DC, negative tip, from NUX's ACD-006A adaptor, which comes in the box. The manual gives the current draw as under 280 mA, and Bonedo's review measured about 230 mA in use, which is the figure to plan for on a shared pedalboard supply.
How do you build a patch on the NUX MG-400?
Pick the amp model first, then set its controls, then add the blocks in signal-chain order: drive before the amp, time and modulation after it. A patch built the other way around ends up compensating for the wrong stage. Tonelify returns the model, the order and the parameters together.
Does Tonelify support the NUX MG-400?
Yes. Name it in the tone matcher along with the song you are chasing and the settings come back adapted to it. Gear does not need to be in the catalog for a match to run.
Sources
Panel, specifications and dates checked against these on .
- NUX: MG-400 user manual (PDF)
- NUX: MG-400 product page, with the GEN2 firmware notes, firmware, QuickTone and drivers
- NUX: MG-400 firmware update guide (PDF)
- Premier Guitar: Nu-X Launches the MG-400 (22 September 2022)
- gearnews: NUX MG-400 (7 October 2022)
- Bonedo: Nux MG-400 Test (23 December 2022, German)
More NUX gear
Similar multi-effects units from other makers
Settings for the song you are chasing
Name a song and Tonelify reads the documented rig behind the recording, then writes the settings for a rig with the NUX MG-400 in it. A first plan starts with 7 days free, $0 today.